20 Most Recent 1997 Honda CB 250 Nighthawk Questions & Answers

not a car, moved yah'cam chain/guide failures.it must be inspected. get it serviced is the answer.or learn how.id not drive it, not me,the cause must be found first.and I have no xray vision yet.

Change gears shaft bearings.

THERE ARE TWO EARS INSIDE THE WHEEL AND THE SPEEDO DRIVE UNIT HAS TO FIT IN THIS EXACTLY OR IT WILL NOT GO BACK TOGETHER.

Usually this would be the side stand sensor. I would have thought that it would be normally closed circuit to operate though. Have you tried linking out the sensor wires? ie joining them together.

Either engine can be made to fit the frame but lining up drive sprockets will be difficult without swing arm mod

Just a guess, but sometimes when a load is applied to some motors, if they stall or bog down, they probably need a valve adjustment.

If the left side is ok, it is probably a broken earth on one of the right side indicators (blinkers). If both sides come on ok but don't blink, it's probably the relay

Once you replaced the sensor it should be all fine

Sound like the cable may be damaged or is getting pinched somewhere. I would start at the handles and work your way down more than likely its at the top, Handle could be crumpled in slightly with the fall and pinching the acc-cable

sounds like fuel air mixture wrong or your engine is starved of fuel ..clean all filters

Backfire when throttle down can be;1. dirty carbs that are running lean and need cleaning. Also the rubber grommets that hold the carbs can be leaking at the backside or even dry rotted.2. no air filter3. broken or open vacuum lines4. an aftermarket exhaust that needs rejetting or an open exhaust system

hi its been quite a while since i have done 1 of these but if the bike has the original forks on it i am sure you can do this without removing the complete fork of the bike, after suporting your bike you can chose to completely remove the fork if you wish, i would first try it without removing the complete fork first, remove front wheel, remove front mudguard and inner stabilizer, keep all bolts together in a safe place, you will need a clean container, to catch the fork oil,(TIP) if you catch all the oil and alow time for it to drip dry you can measure the amount of oil that was in the fork by pouring it from the container into a measuring jug, this will save time if you dont know the specific amount of oil required, to drain the oil you will need a suitable alun key to undo the fork leg/tube securing bolt, you will find this in the lower of the fork leg where the wheel spindle fits, turn the key anti clockwise to undo it, hopefully it will crack loose, if it just spins and doesnt undo you may need air tools to shake it loose, once the bolt is undone secure the fork leg and remove the bolt, the oil will then desperse from the fork, moving the fork lower slowley up and down will help rifle the oil out, make sure the sealing washer is on the bolt or you may have to fish around inside the old oil for it, when you are happy all of the oil has been removed, carefuly pull the fork leg down all the way until it comes of the stanchion, pour any oil into your container, if when you pull on the leg it does not come off this will be because the fork stanchion on your bike has bushes that are fited to it, and not to the lower leg, in this case you will have to remove the whole fork, remove, the dust cover from the fork leg inside you will see a circlip remove this and washer, remove cap from fork top and pour out your oil, and fork spring noteing direction , remove the lower bolt, fix the fork lower in a vice at the very bottom of the leg wher the flat area is, do not grip tubular area,then to remove the seal you will need to push down on the fork stancion to its lowest point, and sharply pull up useing the stancion as a hammer, repeat this untill your fork seal is removed, replace in reverse order, good luck hope this helps. paul

To read the serial number on a Honda PC50 moped, follow these steps: Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places: Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567. Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body. Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it: The 9th digit of the VIN is a check digit. The 10th digit represents the year code. For example: A = 1980 B = 1981 C = 1982 D = 1983 E = 1984 F = 1985 G = 1986 H = 1987 J = 1988 K = 1989 L = 1990 M = 1991 N = 1992 P = 1993 R = 1994 S = 1995 T = 1996 V = 1997 W = 1998 X = 1999 1 = 2000 2 = 2001 3 = 2002 Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model; Additional Resources: If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped. Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.

Question edited for clarity and add magic word. The Owner's Manual covers basic repairs and is free. https://www.google.com/search?q=honda+anf125+innova+service+and+repair+manual

Honda ANF125 Innova Service and Repair Manual

Google Books https://books.google.com > ... > Repair & Maintenance The aim of this manual is to help readers get the best from their motorcycle. It provides information on routine maintenance and servicing and the tasks are ...

Honda ANF125 Manuals

ManualsLib https://www.manualslib.com > ... > Scooter Manuals and User Guides for Honda ANF125. We have 1 Honda ANF125 manual available for free PDF download: Owner's Manual ...

Honda Scooter ANF125 Innova Scooter (2003 - 2012)

Haynes Manuals https://haynes.com > en-gb > anf125-innova-scooter Detailed repair guides and DIY insights for 2003-2012 Honda Scooter ANF125 Innova Scooter's maintenance with a Haynes manual. ..

The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.

Question edited for clarity, but no idea what you mean by - "What do I need to do to get the gay? The clutching gauge in again?" You issue is probably that all the clutch plates are glued together. Leaving a bike for 21 years will do that. https://www.google.com/search?q=1985+Honda+Gold+Wing+1200+stuck+clutch ..

Check the wiring, especially the engine earth lead.

On the bottom of your speedometer on the left side there is 2 buttons press the far left one for a couple of seconds and the light should go on