20 Most Recent 2000 Honda VT 125 Shadow Questions & Answers

sorry I do not have a diagram at this time but will send one or a link when possible

The problem sounds like it may be the exhaust manifold gasket,but you can also check for any holes in the pipes etc...

Go to your local auto parts supply store and they usually have service manuals for cars, trucks, bikes, etc. If they don't have yours in stock, you can ask them if they can order it.

It sounds like your fuel line is clogged. Check to see if there is a filter on the fuel line and change it if there is. If not, take off the petcock valve (under the tank) and clean it out. Good luck.

Plug gap..035.Hope this helps

No this is not normal. probably a problem with an earth lead not making a good connection.

Have the timing chain inspected. Normally these can be adjusted easily

Mine is a standard thread.
Clockwise to tighten, anticlockwise to loosen.

The only thing I can think of is a broken gear tooth on the outer clutch hub. Remove the right engine side cover and check the clutch hub and the crankshaft drive gear.

The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.

Question edited for clarity, but no idea what you mean by - "What do I need to do to get the gay? The clutching gauge in again?" You issue is probably that all the clutch plates are glued together. Leaving a bike for 21 years will do that. https://www.google.com/search?q=1985+Honda+Gold+Wing+1200+stuck+clutch ..

Check the wiring, especially the engine earth lead.

On the bottom of your speedometer on the left side there is 2 buttons press the far left one for a couple of seconds and the light should go on

Question edited for clarity. The RC26 has a few modifications, but nothing that should alter the wiring.

1986-1987 - VFR700F / VFR700F2 (RC26)

The "Tariff Buster"[ 700cc VFR700F was almost identical to the 750cc version, with minor changes to graphics (no 750 on the lower fairing), shorter stroke, different cams, and altered ignition timing. Otherwise the VFR700F2 was mechanically the same as the standard F, but had an upgraded rear shock and fork internals alongside square gauges. Wiring diagrams and manuals https://www.google.com/search?q=1987+honda+vfr+700f+wiring+diagram ..

For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components. For the CBR929RR, the cylinder head bolt torque specifications are typically as follows: 1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs) 2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs) It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model. When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket. Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly. As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.

found this on eBay copy and paste Picture 1 of 1 Vesrah Oil Filter for Honda VT250C V Twin Magna 1994-1995

. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod. I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.