2005 Honda VT 600 C Shadow - Answered Questions & Fixed issues
Carburator leaks gas when cycle is started or running from what looks like vent hose?
Sounds to me like your float valve is obstructed by some debris. This is causing it to stay open and leak fuel. Better it leaks to your vent hose than it leaks in your engine and contaminates your oil.
You need a proper carb cleaning. Not some run in the gas tank sh*t. If the tank wasn't full when parked, chances are there is rust in the fuel system to get this out you need to disassemble the carburetor and thoroughly clean it.
Try not to ride the bike til you do this. It's a fire hazard.
Fuel dripping fron carburator drain
This is caused by the fuel float in the carburetor not completely closing the fuel needle valve. Either the float is not properly adjusted, the float has failed or there is a small piece of dirt or rust blocking the valve from closing.
I bought a 2005 Honda Shadow VT600C/CD because it
Use only JASO MA certified oil in the 10w-40 or 20w-50 depending on the outside temperature. Do not use any oil with Energy Conserving on the label it will shorten the wet clutch and gear life. Amsoil and Mobil 1 make good synthetic oils.
Will not idle
Your carbs are dirty and need to be cleaned. A tank of bad gas or old gas can gel up the jets. You buy gas, drive home, and when you get there the bike stops idling. Light gelling can be fixed by draining the carbs (screw on bottom of bowl), pulling the fuel line off the tank, and squirting some motorcycle carburetor cleaner down the fuel line. Plug the fuel line back in turn on the gas and start up the bike. If that doesn't work, using the same procedure buy some Chevron Techron fuels system cleaner, pour directly into the carbs and let sit over night (also drain tank and heavily treat one gallon of gas and put in tank) Fire up bike and let run ,idle, slow drive for 5 to ten minutes. This will usually get cycle idling without disassembling carbs. If it still wont idle you will have to take off the carbs, disassemble and clean blowing through the jets and jet passageways.
How do i install saddlebags on a 2007 honda shadow
I've got a 2007 Shadow and recently put on a set of saddlebags. What you do is use a large allen wrench or star wrench on the seat strap to take out those two bolts, and then you slide the seat towards the back of the bike (or perhaps you need to slide it to the front, I forget, its just the "picture-hanging" connection, <=0 is the shape of the hole on the seat, and on the bike beneath it is a peg, with the seat hole large enough to slide the peg through, but once you shift the seat to its natural position the head of the peg is at a place too narrow to come off, hence the sliding motion to remove it) . Then it is smooth sailing, just lay your saddlebags over the peg with the seat removed, and try and put the seat back without disrupting the bags too much, which can be hard since its a pretty snug fit. Hopefully that helped, I don't know if the request was talking about post market support frames or something
4/26/2010 6:51:12 PM •
2005 Honda VT...
•
Answered
on Apr 26, 2010
•
1,229 views
Odometer screww
You should find a small screw in the center of the end of the knob - remove the screw then just pull the knob out.
Speedometer is not functioning properly in honda
Hi...
first check your speedometer cable if it is not destroyed. This is caused by pulling your motorcycle reversed or backwards too often. So, all you have to do is replace it. Here in the Philippines it will just cost you P70.00. That's almost $2 USD. I don't know in your country.
You have a nice Honda activa motorcycle!!!
2007 Honda Shadow VT600C won't start have new battery and plugs, and coil pack, new fuel filter, velocity stack, rebuild carb, loose choke cable to the carb.
I'm sorry to hear about the trouble you're experiencing with your 2007 Honda Shadow VT600C. If you've already replaced the battery, spark plugs, coil pack, fuel filter, and performed maintenance tasks such as rebuilding the carburetor and checking the choke cable, there are a few more things you can try:
1. Fuel delivery: Check that the fuel pump is functioning properly and delivering fuel to the carburetor. Ensure that the fuel lines are clear and not clogged.
2. Ignition system: Verify that the ignition switch is in the "ON" position. Check the ignition fuse and wiring for any potential issues. Ensure that all connections are secure and clean.
3. Air intake and filter: Make sure the air filter is clean and not obstructed. Ensure that the velocity stack is installed correctly and not causing any air flow issues.
4. Compression test: Perform a compression test to check the engine's compression. Low compression could indicate a mechanical issue within the engine.
5. Starter motor: Check if the starter motor is engaging properly and turning over the engine. If the starter motor is not working, it may need to be replaced.
6. Wiring and electrical connections: Inspect all wiring and connections related to the ignition system, starter motor, and battery. Look for any loose or damaged wires that may be causing the starting issue.
If you've exhausted these troubleshooting steps and the problem persists, it may be best to consult a professional motorcycle mechanic or Honda dealership. They have the specialized knowledge and diagnostic equipment to pinpoint the exact cause of the starting problem and recommend appropriate repairs.
Please remember to exercise caution and follow proper safety procedures when working on your motorcycle.
Not finding what you are looking for?
