20 Most Recent 2005 Honda FMX 650 Questions & Answers

Semi-Synthetic, 10w-40the location you might try the auto parts store where you go to buy the oil.

charge the battery up...& clen the carb if its been stood all winter

If you did indeed overheat the engine to the point that is stuck, you would probably know it by the antifreeze being poured all over the ground. The bike would be really hot just sitting on it. It would smell like antifreeze and just smell hot.. I know, smell hot? but an engine that has been ran to hot has a pretty distinctive hot smell... It doesnt sound like an overheating situation if none of the above happened. A bike that is overheating will begin to loose power before it stops. LIke lacuna said, everything inside of the engine will start to expand from the heat and the piston will stick in the cylinder. Most of the time when this happens, the bike will cool off and restart. But, usually with problems. Warped or cracked head, cracked block, broken piston rings. These engines are aluminum and dont like to be overheated and warp really easy. If the engine is really hot, it will not turn over until it cools down enough. Im not saying it couldnt have overheated and then restarted without any problems, its happened before, but just not likely. But, if this is the case, take lacunas advice and change all of the fluids. Your oil will be nasty. Maybe get ahold of the previous owner and see if it has had any probems. It kinda sounds electrical to me. as long as the above overheating signs didnt happen. If you dont think it was overheating and it happens again, try to push start the bike to see if the engine turns over. even putting the bike in second or third gear just see if you can move the bike back and forth. If nothing else, you'll at least know its not locked up.

The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.

Question edited for clarity, but no idea what you mean by - "What do I need to do to get the gay? The clutching gauge in again?" You issue is probably that all the clutch plates are glued together. Leaving a bike for 21 years will do that. https://www.google.com/search?q=1985+Honda+Gold+Wing+1200+stuck+clutch ..

Check the wiring, especially the engine earth lead.

On the bottom of your speedometer on the left side there is 2 buttons press the far left one for a couple of seconds and the light should go on

Question edited for clarity. The RC26 has a few modifications, but nothing that should alter the wiring.

1986-1987 - VFR700F / VFR700F2 (RC26)

The "Tariff Buster"[ 700cc VFR700F was almost identical to the 750cc version, with minor changes to graphics (no 750 on the lower fairing), shorter stroke, different cams, and altered ignition timing. Otherwise the VFR700F2 was mechanically the same as the standard F, but had an upgraded rear shock and fork internals alongside square gauges. Wiring diagrams and manuals https://www.google.com/search?q=1987+honda+vfr+700f+wiring+diagram ..

For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components. For the CBR929RR, the cylinder head bolt torque specifications are typically as follows: 1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs) 2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs) It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model. When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket. Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly. As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.

found this on eBay copy and paste Picture 1 of 1 Vesrah Oil Filter for Honda VT250C V Twin Magna 1994-1995

. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod. I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.

The problem might be with the air filter, and if not there are a few other things that could be causing your Shadow engine to bog down on acceleration. This includes a dirty carburetor, carb adjustment issues, or other internal problems like damaged vacuum lines or a cracked manifold

Question edited for clarity. Question moved from Honda Cars. I haven't seen one of those for 40 years! The Braided cable goes to battery negative - They normally have a Red Cable to the battery Positive + And if I recall, there is an inline fuse in the positive? Here is the cable https://www.ebay.com/itm/NOS-OEM-Honda-Cub-50-70-C70-K1-C50-C65-M-CA102-C102-Cable-Earth-Battery-Ground-/172214475304?_ul=IN and here https://www.ebay.com/itm/225016392400 Service manuals x two :>D

Honda C102 Service manual

Honda 4-stroke.net https://4-stroke.net > honda-c102 > downloads > 440-... You can go to our downloads and grab yourself a copy! Download the Honda C102 Service Manual in the following format: pdf Service manual for Honda C102 (1.93 MB).

• Workshop manual for Honda C102 (1961)

  https://4-stroke.net > honda-c102 > downloads You can go to our downloads and grab yourself a copy! Download the Honda C102 Service Manual in the following format: pdf Service manual for Honda C102 (1.93 MB).

Service Repair Manual Honda C100, C102, C50,C70, C90

Blogger http://myhondac100.blogspot.com > 2013/10 > servic... Oct 21, 2013 - Service Repair Manual Honda C100, C102, C50,C70, C90. http://www.servicerepairmanualonline.com/4449/honda-super-cub-50-c50- ...

limited info generic answer get a meter and test the components that you replaced as well as battery- fuses - kill switch -------do an online search using year make model for a service their are many free ones