20 Most Recent 2007 Suzuki GSX-R 600 Questions & Answers


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.gsxr.com/7-general-gsxr-chat/8082-adjusting-rev-limited.html
https://www.youtube.com/watch?v=fHN5cWSKMm8
https://www.manualslib.com/manual/813897/Suzuki-Gsx-R750.html#product-2007%20gsxr%20600
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

2007 Suzuki... | Answered on Jun 08, 2019


means you're having a problem with your secondary throttle position sensor. very common problem with suzuki.

2007 Suzuki... | Answered on May 22, 2019


Hi, Dan coolant in the oil usually only comes from a few places the following scenarios will help you decide which.
1. A blown head gasket will allow coolant to seep into the combustion chamber past the rings and into the bottom end mixing with engine oil causing it to look milky. It will also burn with the fuel charge and exit the exhaust as white smoke, in severe cases, it will drip coolant from a low slung muffler. There could be a loss of compression. Another tell-tale sign is the pressure from the combustion chamber will force coolant out of the overflow at the reservoir.
2. A faulty water pump caused by old age with bearing failure or a failed oil seal. The tell-tale signs are water leaking from the weep hole and complete loss of all coolant fairly quickly causing the engine to overheat.
3. A cracked cylinder wall or cracked cylinder head and the tell-tale signs are pretty much the same as a blown head gasket.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.gixxer.com/forums/237-07-08-gsx-r1000/667225-coolant-my-oil-oil-my-coolant.html
Flushing Coolant on GSXR
Suzuki GSX 400F Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

2007 Suzuki... | Answered on Apr 22, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
torque specs
http://www.venold.com/tl1000s/specs/torque_specs.html
https://www.manualslib.com/manual/813897/Suzuki-Gsx-R750.html#product-2007%20gsxr%20600
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

2007 Suzuki... | Answered on Apr 05, 2019


chech side stand swich

2007 Suzuki... | Answered on Mar 23, 2019


Hi, Michaelclont for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
k7 600 stator and rec reg replacement Suzuki GSX Motorcycle Forums Gixxer... How to replace Stator on Suzuki GSXR 600 06 07 08 09 15 Suzuki GSX R600 Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 04, 2018


Hi, Gushb69 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2007 Suzuki GSX 600 wiring diagram Google Search
Suzuki Motorcycle Wiring Diagrams
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 04, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
GSXR 600 RECTIFIER REMOVAL AND INSTALL
GSXR 600 750 K6 K7 Regulator Relocation charging problem FIXED
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 03, 2018


Hi, Freeridek47 and the usual suspects are:
1. Instrument wiring harness connector corroded.
2. Faulty power or ground wire at the tachometer.
3. Broken, loose or corroded tachometer wire at the coil.
4. Short between the ignition coil and the tachometer.
5. Broken tachometer cable.
6. Faulty tachometer.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Speedo Tach not working 2007 Suzuki GSXR 600 Chicagoland Motorcycle Repair Tachometer not working Suzuki GSX Motorcycle Forums Gixxer com Suzuki GSX R600 Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 02, 2018


Hi, Anonymous before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2007 GSXR600 charging issues Suzuki GSX Motorcycle Forums Gixxer com
2006 Suzuki GSXR 600 Not Charging
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 02, 2018


Hi, Tyler before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2007 GSXR600 charging issues Suzuki GSX Motorcycle Forums Gixxer com
HOW TO CHECK YOUR CHARGING SYSTEM and CHANGING the STATOR and REGULATOR...
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 01, 2018


Hi, Mike you need to perform the following tests:
1. Fill acid type batteries to proper levels.
2. Charge battery overnight at 1-2 amps you need 12.5 volts or better after charging and it must be able to pass a proper "LOAD" test you may have cursory readings of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries have this issue more so than lead-acid types.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Hook up battery positive cable, then with your multimeter on the milliamp scale connect one lead to the negative battery post and the other lead to the ground cable. The meter should read 3 milliamps or less, 10 milliamps with a radio, 15 milliamps with radio and CB. If your multimeter reads higher you need to isolate the circuit by pulling fuses and circuit breakers one at a time and observe multimeter for a drop in amperage then get out your test light and track down the short in that circuit.
5. Hook up the multimeter to the battery set it to DC volts and start the engine if multimeter falls below 9.0 volts while cranking you need to perform a proper load test on the battery and replace if necessary.
6. With the engine running at 3600 RPM, the battery should read 14.3-14.7 volts if not continue tests.
7. Unplug the voltage regulator from the alternator at crankcase by the front of the primary cover.
8. To test voltage regulator go to https://www.youtube.com/watch?v=F8EjV0IjW9Q
9. With the multimeter set to the ohms scale, with one lead grounded, touch an alternator pin ohmmeter should read infinity, if not replace the stator.
10. With both leads touching alternator pins, multimeter should read 0.1 to 0.2 ohms on 1989 and later models. 0.2 to 0.4 ohms 1988 and earlier models, if not replace the stator.
11. With the multimeter set on AC volts scale, both leads touching alternator pins multimeter should read 16 to 20 volts AC for every 1000 RPM'S 1989 and later and 19 to 26 volts AC for every 1000 RPM. If not replace the rotor.
12. Check for excessive wattage load from the headlight
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Battery draining even when my 2007 gsxr 600 is turned off Suzuki GSX...
How to diagnose fix parasitic draw on your motorcycle
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Nov 01, 2018


Hi, Lasvivoras before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
07 gsxr 600 won start GSXR com
GSXR 1000 Wont Start Troubleshooting Partzilla com
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Oct 31, 2018


Hi, Anthony and the usual suspects are:
1. Neutral light bulb burnt out.
2. Faulty neutral switch.
3. A loose bulb in the socket.
4. Faulty wiring from the neutral switch to the light.
5. If the neutral light stays on while the bike is in gear the wire from the light to the neutral switch is grounded.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
desperately need help neutral light flashing with keys out Suzuki GSX...
neutral light issue Sportbikes net
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Oct 31, 2018


Hi, German if some or all of your instrument cluster goes dark/blank immediately upon startup or a few minutes later riding down the road the usual suspects are:
1. Blown instrument fuse.
2. A bad ground in the instrument circuit.
3. Faulty wiring before or after the fuse.
4. Faulty wiring or connector between the fuse and the instrument cluster.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Speedo Tach not working 2007 Suzuki GSXR 600 Chicagoland Motorcycle Repair
Speedo and Tach not working Suzuki GSX Motorcycle Forums Gixxer com
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Oct 30, 2018


Hi, Anonymous and the usual suspects are:
1. Dirty or clogged air filter.
2. Faulty spark plug.
3. Bad Gas.
4. Improper oil level.
5. Improper chain adjustment and lubrication.
6. Low tire pressure.
7. Dirty or contaminated carburetor needs cleaning and tuning.
8. Clogged or faulty fuel pump or injectors.
9. Improper valve adjustment.
10. Slipping clutch.
11. Improper timing.
12. Low compression.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Is it possible to lose horsepower Suzuki GSX Motorcycle Forums Gixxer com K6 GSXR 600 engine stalling loss of power while ri Suzuki GSX R600 Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Oct 30, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2006 Gsxr750 How to Check F1 light or Fl and Get Code Fast easy and Free
Suzuki Fault Codes
Suzuki GSX R600 Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Oct 30, 2018


Hi, Anonymous and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
8. Damaged petcock diaphragm allowing fuel to flow through the vacuum line into the combustion chamber.
9. Contaminated fuel tank.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Fuel Leaking into Cylinder from Carbs Suzuki GSX Motorcycle Forums Gixxer...
Carbs leaking Here is how to fix it
Suzuki GSXR400 GSX R400 1984 1987 SERVICE MANUAL Download Manuals Technical $15
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

2007 Suzuki... | Answered on Sep 22, 2018


Could be ignition fuse. If not that then check the large block connectors which are usually located on the left hand side at the front of the bike behind the cowling beneath the handle bar. These connectors are notorious on GSXR's

2007 Suzuki... | Answered on Jan 17, 2018


have you checked compression on it, plugs out comp tester in crank see what happens, then a small amount of oil see if compression goes up some,

2007 Suzuki... | Answered on Jan 06, 2018

Not finding what you are looking for?
2007 Suzuki GSX-R 600 Logo

142 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers

ROB

Level 3 Expert

858 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GSX-R 600 Suzuki

  • GSX-R 600 Suzuki

Most Popular Question

main fuse keeps blowing

  • Motorcycles
Loading...