20 Most Recent 2002 Yamaha DT 125 R - Page 7 Questions & Answers

Neutral should be between 1st and 2nd. Likely cause could be worn or bent shift forks and/or shhift drum. Both are inside the transmission and will require engine removal and case splitting.

Another less likely, but easier repairable cause could be a damaged or miss aligned shift linkage inside right side cover of engine.

A dealer run 11 to 15 hours at there labor rate .Plus all the parts necessary to complete the repair

Check the wiring exiting the crankcase up to the rectifier/CDI unit and ignition coil. Look for excessive squashing, pinched or burnt (very stiff) wiring. Check all connections are firm and free of corrosion. Ensure plug lead is not arcing to frame or engine when in place. Make sure ingition coil is FIRMLY earthed at mounting point. A good tip is to run an earth wire from the head bolt to the frame. Thoroughly check any "kill switch" wiring as moving handlebars, throttle cable etc whilst kicking over may interupt electrical circuit. It is common for wiring to eventually get caught up in the steering "stops" on the lower fork clamps, cutting or severely damaging wiring. The wires exiting the crankcase come from the generator and without a rotor puller they will remain unsighted behind the generator rotor. You can easily remove the cover however, and check grommet where loom enters for pinched or flattened wires.
Check the site below (scroll down for your Model/Year) It has exploded view diagrams of all the pertinent parts to see your bike going again. Cheers.

http://www.cmsnl.com/yamaha-motorcycle_model16707/

your battery helps the voltage regulator. you need a good battery, on old machines if one light goes out others will burn out also. make sure all of your bulbs are good. but make sure you have a good battery (6 Volts) that is hooked up and your main fuse is good.

It is a simple job to rebuild a dt125r as it is 8 or maybe 9 bolts holding the head on, drain the coolant into a container so you con use again, undo the 5 bolts holding the cylinder head on(after taking the spark plug and coolant pipes off) after this undo the cylinder bolts should be 5 bolts to undo(12mm socket or spanner)t take the cylinder off the undo the gudgeon pin holding the piston on, at this point all you should see on the engine is the engine block with a con rod coming out of it. After you have the engine dismantled measure the bore diameter and then go to B&Q or any hardware store and get a circular sanding head for a drill that is maybe 5mm-10mm bigger than the bore, put the sander inside the bore on full power and hold it there for atleast 1minute and 30seconds, this should get rid of all of the score marks on the bore do the same to the piston(go round all score marks to make it smooth), get som gasket paper(or a engine set for dt 125r but gasket paper is only £1.09 from most shops) blue tak it to the top of the bore them go aroud it with a hammer very lightly so u have a gasket to fit the head on both ends, use a line of gasket glue(big line about 5mm in depth) all the way around the head and assemble the engine, this will only be temporary untill you have to do agen but it is cheaper than spending £150-£190 on new bore and piston.

timing chain broke

THERE ARE NO LIGHTS ON OF ROAD BIKES, YOU NEED TO LOOK FOR SIMILER COLOR WIRES COMING FROM ANY PART OF THE BIKE AND CONECT THEASE

yep sounds like it needs rings the dt50w usualy has lots of torque down low so if you are having ti rev the **** out of it somthing is not right only other option would be that the previous owner messed with the sprokets to get more speed but lost low end torque
good luck

Use graduated measuring bowls and remember RELAESE pressure first before doing thisl...then crack open the drain scews and messure amount..this will ball park it. use 10 weight oil to replace. dont put more that a couple pounds of air backin the shocks they dont need nuch more then 4-6 psi. if you us ea gas station to inflate only squirk for as second then measure you might blow the seals..remeber very little air.

http://www.motoverse.com/tools/vinDecoder.asp

Try here

http://www.carlsalter.com/motorcycle-manuals.asp

A very useful site
John

it may have a dirty carb remove the float bowl and clean out the **** that may be inside, it may be as easy as that reassemble float bowl and start, if problem is not fixed remove the carb disassemble and clean then reassemble and try again to run the bike, remove the fuel hose from tank and ensure that a good flow of fuel is coming through fuel delivery hose from tank.

u made my day by goin oldschool-sounds like the floats r stickin or bent-if u buy a clymer manual theyll show in detail disassembly n specs-walnecks classic mag would be worth a google

i have the same problem. i have recently bought a 1998 dtr, but when we had a closer look at the engin, it wasnt worth keeping. so managed to get a 2006 engin. i fitted this. but the bike seems reallys slow. I then opend the powervalve. but the bike boggs out just as i get in to the power band. i was told to re jett the bike to a 260. so will be getting that done soon. will tell you what it goes like mate.

try decarbonize piston and rings, for two stroke like DT 125 check the 2t oil pump

If the floats are sticking then bang the side of the carb gently with a hammer handle to dislodge them
Ride Safe
Bike-doc

Please mark this as useful (if it has been!!)

With the rattle, i would true the crank. Was there ever an abrupt stop (chain came off and wedged, locked up back tire, etc)? That would indicate crank.

If it had points i'd say they were floating.

Sometimes a plugged exhaust will limit power at a certain rpm, but not explain the rattle (i'm imagining vibration, but it could be something benign). Good luck.

you should check the cooling system if you don't have one then your gonna have to deal with it unless its something else its a different problem but that happens to my 3 wheeler that has no cooling system

hi kev,

thank you for using fixya.

i'm a 2-stroke fan myself, all my bikes are 2 stroke. with the issue you currently have, i would say that the culprit will be the following.

1. carb mixture for oil, air and gas. you may need to have this tuned making sure that the 2-t oil is not more than the gas.

2. body {background-color: #FFFFFF;font-family: "Verdana"; font-size: x-small;} p { margin: 0px 0px 0px 0px; } overheating, there are many points for a 2 stroke engine to overheat even on in idle, one reason is too much oil or too little oil (transmission oil that is). when it overheats, the gas/oil/air mixture will be heated and too denced to burn, leaving it with low combustion and smokey burn.

best way to get through this is to check your piston and rings of any scratch for a possible blow by, and have parts replaced if possible. for the carburator, just set the timing and the tuning to 1:4:5.

should you have other questions, please let me know.

regards,

voodoo

This is a highly ill - eagle act to do. In the old days we would put an electric drill on the drive cable, but now they make them tamper proof so they only go one way. The bezels are crimped on so you can't get inside them. I expect modern one may be electronic. How will your insurance company know what mileage you have done? I have never known an insurance cancel or fine due to mileage. You should have just disconnected it when you got close to the limit. Buy a used one and use them for 6 months in turns. There are two or three here 23K and one with 36k https://www.google.com/search?q=2002+yamaha+sr125+speedometer ..