20 Most Recent 2007 Yamaha XT 125 R - Page 2 Questions & Answers

Check your battery voltage ... then check the start solenoid for proper operation.

try ebay or a motorcycle salvage

Turn the ignition on and hold the pass light button in when it says either endr or ntrd depending on whether your bike is an enduro (off road) or the other one (don't know the name).

Try unplug its harness connector behind it and use compressed air to clean it. before you plug it back on put a little of lithium grease in the connector to prevent this to happen again.If the problem persists then you should see a dealer cause the water penetrated inside the cluster.

Sounds like your bike is running to rich. Find and remove your air cleaner element, if it is clogged that is your problem. Easy way to tell is to get a torch and hold it behind your filter if you can't see the light or it is very subdued your filter needs to either be cleaned or replaced.
If it isn't your element then your carb might be fouled or your leads may be breaking down

Possibly a fuse , but you may need a new battery, they dont always charge up.If they have sat uncharged for a while.
Shouldnt be the CDI

Not Idling there are multiple reasons not only carb.
1, Improper Timming 2, Compression leak 3, Bad spark-plug 4, chocked Airfilter.
clean the spark plug and check the firing clean or replace airfilter check timing check for leaking gasket in cylinder and cylinder head check valve seal check all these as I mentioned order it will help.

Try this :-------- With the new battery connected the speedo should flash up enduro or motard. When it flashes from enduro to motard turn igniton on but dont start.
---------------
When it flashes again to enduro press the blue mode button on the front of the left handlebar. It should revert back to the correct mileage settings.-------------
----------------------- But if that is not helping, then you can reset the speedo.To reset speedo, remove the speedo connection and reconnect it after 5 minutes.This resets the speedo.To do this undo the two Allen bolts on the top of speedo whilst holding the nuts underneath then unclip the wire connector underneath speedo (lift little white tooth clip and pull) after you have removed the speedo for 5-10 minutes put it back on to the white clip turn the key into the central position (not starting the engine or to steering lock) then your speedo should be flashing endurance and motard depending on which you own (endurance being the "r" model and motard being the "x" model) when it flashes onto your type of bike turn on the ignition to the right and you should have the correct speed reading for your bike.----------- Also you can try this procedure :----------------- a much simpler way to change the display from enduro (the r model) to motard ( the x model) and vis versa, fisrt remove the seat by undoing the 2 allen key bolts near the back of the seat, then all you need to do is disconnect the battery for about 5 mins to reset the screen(always disconnect the negative first),then when you connect the battery back up the screen will say enduro and then notrd(this stands for morard) turn the key on and then when it flashes your model hold the mode button on the left handlebar(the little blue button) and then the screen will come to life and will say 125 and ethier notrd or enduro below the number 125, and this is the mode you have selected. ------------------ This will help.Thanks.Helpmech.

try this site sir http://diagramwiring.net/?s=2007+Yamaha+XT+125+R

It sounds to me like it is in need of a service. I would get a dealership to service it and then advise you on what to do in the future for yourself.

http://www.haynes.co.uk/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10001&storeId=10001&productId=49301&langId=-1&parent_category_rn=15015

Remove the air filter and clean or replace it. Get a can of spray starter fluid and spray into the carb before mounting the filter. Chances are the new spark plug is wet from gas.

Please detail your location/area.

please check speed cable

First, check the rear brake master cylinder for fluid. Then check down the brake line to the caliper looking for leaks. Lastly check the caliper for leaks.
If the resevoir is low/ empty and you add fluid dont forget to bleed the system.

You may have supermoto wheels on a speedo that is set up for enduro wheels or vice versa. I had the same problem myself. A quick visit to my local dealer and £5 later the problem was fixed.

When you start it up the bottom of the speedo will flash up either "motard" or "enduro" depending on which setting it is running on.

check at the manufacturers site for this info ... or if you really want to look try www.archive.org search service manual for your brand.

somewhere probably on the right hand side of your bike, there is a screw cap with a handle that looks sort of like a thumb screw. Undo it ... it it has oil on the botton, you found it.

£50 for oil what the **** buddy do it your self i say just warm the bike for 5 mins this makes the oil thinner unscrew the plug at the bottom let it drain into a bucket and then once drained put the plug back in retighten it and unscrew the filler cap and fill with oil until it reaches 3-4 full on sightglass any more questions on how to service it buddy get back to me

It should be in your manual . If you dont have one you should . Or if your cool with your local dealer . Ask them they might tell you .

Disc rotors are replaced when they wear down to the minimum thickness (stamped on the disc) Pads are replaced when they are down to 0.5mm remaining....