2008 Yamaha YZF-R125 - Answered Questions & Fixed issues
YZF R125 Engine Management light on, but engine runs ok.
I had this exact problem with my r125. My speedo just read 0 and warning light came on. This is caused by a faulty speedo cable. You need to unclip it from under the clocks (the white connector running to the side of the front wheel) and take the front wheel off. Then replace the speedo sensor with a "new" one (quite fiddly to put all back together). Got mine off eBay for just a few pounds. When it's all back together, the warning light will still be on, but when you ride off and the speedo reads something other than 0, the light will go off, and problem solved! When your wheel is off, take the time to re lube the axle, makes putting the axle back in so much easier and your front wheel will turn so smoothly and freely. Make sure you keep note of how the spacer goes in, and I'd get a friend to help support the wheel as you put it back in, makes it so much easier as it's quite fiddly by yourself.
7/23/2015 12:51:31 PM •
2008 Yamaha...
•
Answered
on Jul 23, 2015
•
1,658 views
Yamaha r125 Body panels
Hi, google cheetah skins, they are a company that offers fiberglass replacment panels and pretty reasonable prices with good fitmant.
10/23/2014 9:34:10 PM •
2008 Yamaha...
•
Answered
on Oct 23, 2014
•
1,760 views
Tyre pressure for yzfr125
tier pressure should be front 25 psi rear 29 psi weight load 0-90kg
front 25 psi rear 33psi weight load 90-185kg both on cold tiers,
3/2/2014 7:18:38 PM •
2008 Yamaha...
•
Answered
on Mar 02, 2014
•
583 views
Symptoms of a bad starter solenoid yzfr125
If the starter wont work, but will if you bypass / short the solenoid terminals together with a screwdriver, and it turns the starter, the solenoid is burnt out.
1/2/2014 3:10:07 PM •
2008 Yamaha...
•
Answered
on Jan 02, 2014
•
325 views
What are all the ingnition timing marks on a yamaha kodiak
hi guys,,,,i have a xmax 125yp....this morning i went out to start the bike,,,and i have a flashing red light next to the key icon,,..can any one help... pleaseeeeeeeeeeee........07892977229
12/22/2013 1:33:36 PM •
2008 Yamaha...
•
Answered
on Dec 22, 2013
•
205 views
How to change gearbox and engine oil
There is a sump plug located at the bottom of the engine. It is very tight. Make sure you have the correct size socket to remove the plug. Use a suitable oil pan under the bike before removing the plug. Once the plug is removed and the oil is drained, stand the bike upright to get the last of the oil out. Get the correct oil, about 1 litre, replace the plug and fill the bike to the correct level using a funnel. Stand the bike upright to check oil level. Do not screw oil dip stick in to test the level.
11/8/2013 6:12:58 AM •
2008 Yamaha...
•
Answered
on Nov 08, 2013
•
342 views
Max speed
mine did 76mph and i used Shell V-power but i weight 12stone so if your less then it will make a differance
6/5/2013 11:18:41 AM •
2008 Yamaha...
•
Answered
on Jun 05, 2013
•
782 views
Wr125r how to remove limiter
you cant remove limiter CDI is limit in eprom.
if you can remove the 4 º degreus ****** in ignition them you will get with full exhaust 20cv.
with 20cv you change the front sprocket from 14 to 15 and your bike topspedd is is 147 kmh.
regards
11/9/2012 11:59:17 PM •
2008 Yamaha...
•
Answered
on Nov 09, 2012
•
1,090 views
Cuts out when i put it into gear
I am not Fimiliar with this motorcycle but where the side stand attaches to the frame get down there a see if there is a side stand safety switch it may be stuck in the if you have that see if you can work it in and out.
10/28/2012 2:32:54 PM •
2008 Yamaha...
•
Answered
on Oct 28, 2012
•
1,104 views
Yzf r125 overheating
Either your coolant has a low top temp range (+102C for example) or you're running on lean mixture. Also check if your thermostat works and opens as it should.
10/22/2012 9:45:00 PM •
2008 Yamaha...
•
Answered
on Oct 22, 2012
•
1,653 views
Not finding what you are looking for?