Question about 2004 Yamaha YZF-R6

1 Answer

04 yamaha turn signal doesnt work

Both front and rear turn signals dont work. I redid bike fairings and all and was finishing putting together when went to wire back turn signals and smelled burning so shut off bike. I konw i wired it wrong but took bike for run after wards (unhooking turn signal wires) and just wanted to make sure it didnt fry computer. Runs great just no turn signals. Would this be due to fuse blew or relay fried? Hopefully thats all... any advice would be appreciated. New at this and trying to save money but looks like costing me. Any help is appreciated. Thanks.

Posted by on

  • 1 more comment 
  • JD Hennessey May 07, 2012

    I appreciate the advice but the headlights work, brake lights work, even the turn signal lights are on but wont flash? any ideas

  • Venturerider
    Venturerider May 07, 2012

    One last question: if you turn on the left turn signal, the left lights come on but don't flash? Same with the right? (Ok, two questions!) If that's the case, it sounds like the flasher unit got fried. I'm not sure where it's placed exactly on your bike, but that's where I'd start. Hope this helps.

  • Venturerider
    Venturerider May 07, 2012

    That's what it sounds like to me. Hopefully nice and easy to get to.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Yamaha Master
  • 59,350 Answers

Hi, JD before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will please click on the links below. Good luck and have a nice day.
http://www.r1-forum.com/forums/104-04-06-r1-mechanical-help/334576-turn-signal-not-working.html
Turn signals dont work
2003 2004 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Sep 20, 2016

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: I'm installing a new rear tail light with turn

use a light pen that you can get from auto parts store to find the hot wires for l and r sides

Posted on Apr 12, 2009

Anonymous

  • 484 Answers

SOURCE: 1994 fzr 500 rear barke light and turn signals not

Your relay is bad. It is right next to the fuse block.

i hope this helps you
-matthew

Posted on Oct 28, 2009

sisadsl

gavin jones

  • 1508 Answers

SOURCE: I went to hook up my new tail light on my 2006

the cover of the fuse box usually tells what they are for, I would expect more than 2 fuses so could be another fuse box

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get to the wire housing on the rear of the 2008 Yamaha V Star 1100 Custom to switch from standard turn signals to LED bullets?


Im not completely familiar with that bike but from pictures and microfiche it looks like there are a couple of bolts under the fairing that when taken out shoild allow you to get into the wiring when you pull the cover out. I hope this helps

I’m happy to assist further over the phone at https://www.6ya.com/expert/anthony_9721e9fd9ba2a150

Dec 03, 2014 | 2008 Yamaha V Star 1100 Custom

1 Answer

Indicators not working fuses ok


Hi, Anonymous before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2005 R1 indicators stop working
http://www.r6-forum.com/forums/73-south-west/154896-help-turn-signals-not-working.html
https://r1videos.files.wordpress.com/2011/04/2002-2003-yamaha-r1-service-manual.pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Feb 08, 2014 | Yamaha YZF-R1 Motorcycles

1 Answer

Yzf600r thundercat 2007rear signals flashing together


Hi, Anonymous you have a wiring issue for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
YZF600R Forums View topic LED Turn Signals
Turn Signal lights are acting like hazard lights ninjette org
Yamaha YZF600 YZF600R 1994 2007 Service Repair Manual PDF Download Manuals...
OEM parts for Yamaha
Yamaha YZF600RP Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 21, 2013 | 1998 Yamaha YZF 600 R thunder cat

1 Answer

Turn signals not working


Ok, consider it kind of like a warning system. You have some blown bulbs and the way it tells you this, it stays solid. The opposite stays off. If it is the back that stays on, then the front bulb is blown and needs to be replaced. Same on all vehicles that use the flasher system.

Apr 16, 2013 | 2000 Yamaha YZF-R6

1 Answer

Is the turn signal flasher relay an open or closed circuit


Hi, Eddie before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will please click on the links below. Good luck and have a nice day.
http://www.r1-forum.com/forums/104-04-06-r1-mechanical-help/334576-turn-signal-not-working.html
Turn signals won flash General Street Bike Discussion
https://r1videos.files.wordpress.com/2011/04/2002-2003-yamaha-r1-service-manual.pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 14, 2012 | 2003 Yamaha YZF-R1

1 Answer

1992 Yamaha XJ 600 Diversion S right turn signal not working


Hi, Jamiepbock before testing any electrical component in the Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
LED indicator lights XJRider com
YAMAHA XJ LED SIGNAL FLASHER RELAY FIX
Yamaha XJ600S 1992 Service Manual
OEM parts for Yamaha
Yamaha Diversion XJ600N Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 24, 2017 | 1992 Yamaha XJ 600 Diversion S

1 Answer

I put longer handle bars on and when i extended the wires the front left wire hit the shock and now the turn signals dont work and i cant seem to find the fuses or a free repair manual


Hi, Larrydoss74 before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Turn signals won flash General Street Bike Discussion
ViragoTechForum com
http://www.groussin.com/multi/XV250.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2005/LIT-11626-18-21_1000.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 10, 2011 | 1996 Yamaha Xv 250 Virago S

1 Answer

Yamaha tdr indicators dont flash


Hi, Lucyemma2009 before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Indicator doesnt flash it just stays on
http://www.apriliaforum.com/forums/showthread.php?179848-LED-Indicators-Won-t-Flash
http://www.yamaha-motor.com/assets/service/manuals/2007/LIT-11626-20-01_ttr125all_1961.pdf
OEM parts for Yamaha
YAMAHA TDR125 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 06, 2011 | 2000 Yamaha TDR 125

1 Answer

I removed my turn signal to get fender painted. I


on the side of your bike in the rear. you have two long brackets where the light mount. under the fender to the brackets from your rear light..then under the fender again to the front from your light this is the rear light harness. if you have a problems go to local auto store i get the hanes shop book this will help considerly..

Apr 18, 2009 | 2006 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?

Open Questions:

0 Answers

FZR 400R Deltabox Exup. wont idle properly Howzit everyone. I have a "small" issue with my FZR 400R Deltabox Exup. So it doesn't want to idle properly(the moment I reduce the idle speed to any point below 3000rpm it continues to drop and dies) and also revving the bike it bogs around 6000rpm doesn't go any higher. When restricting the airflow through the airbox it revs better(all the way to 14k rpm) but still doesn't want to idle as the revs then hang on it's way down. I suspected this was all caused by an air leak somewhere, sprayed some quick start on the boots between the carbs and the intake as well as between the airbox and the carbs with no jump in the revs. Nevertheless I sealed the boots just to make sure they aren't the problem. I then stripped the carb and cleaned it properly, put everything back together, sorted out their syncing and reset the mixture screws to 3.5 turns out(which sounds a bit far out, but thats what the manual said-since then I've tried everything from 0.5 to 4 turns out with no significant effect). Then the cylinder started acting up(not firings- a different cylinder about every third time the bike was started) I then replaced the spark plugs with new ones(NGK cr9ek as per the manual) after that cylinder 1,2 and 3 was firing, but 4 was still dead. I Replaced the coil, leads and caps, still not firing. I checked the compression, which was fine, I checked the valve clearance (cylinder 4 the one intake valve was way out of spec, so i replaced the shim), still not firing. I've got no idea what else could be the problem or what to check next. PS. When i pulled the spark plugs(both new and old) they where burnt black so I'm not sure if my jetting could be out of spec perhaps?

Nov 20, 2019 | SPEC Motorcycles

See all 2004 Yamaha YZF-R6 Questions

2004 Yamaha YZF-R6 Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Israel Pineiro Jr

Level 2 Expert

165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...