Question about 2005 Suzuki RM-Z 250
To adjust your valves you will need a few standard tools and most importantly a set of feeler gauges. You can buy these at any automotive store. The first step is removing the tank and valve cover to gain access to the valve train. You will see both the intake and exhaust cams plus the tops of the valves. This is where you will be measuring with the feeler gauge. The next thing would be to rotate the motor to top dead center. You will need to remove both inspection covers that are on the side of your ignition cover. This will give you access to the timing marks and to the bolt that allows you to turn the motor over.
Check in your manual as to what direction to turn the motor over. You do not want to turn the motor over in the wrong direction. Turn the motor over looking into the inspection (top) hole. You will notice a mark on the fly wheel. When you see this mark come around, look up at the cams. There should be two punch marks on the cam gears that line up with the gasket surface towards the outside of the head. At this point you should be at top dead center compression. Check the lobes of the cam, they should not be touching the valve buckets. If they are touching the valve buckets, this means that you are 180 degrees out of time. Rotate the motor 180 degrees and then start to measure.
After you measure the clearance between the cam lobe and the valve bucket, you will want to write that down. You will then need to check your numbers against the spec's provided in your service manual. If you are outside the specified range, you will need to remove your cams and replace the shims. There should be a chart in your manual that will help you to decide what shims you will need to bring you within the safe range. When dealing with the KXF250 or the RMZ 250, you want to make sure you use the correct shims. There are two types that will fit these bikes, but only one is the correct shim. Shims come both forged and sintered. They look the same until you put them under a magnifying glass, then the difference is very clear. The forged shims have a smooth surface, while the sintered shims have very small cavities. Using the sintered shims will prematurely wear the coating off of the valve stem. This will shorten valve life and cause the valves to go out of adjustment sooner.
Now, after replacing the shims, all that is left is to reassemble your machine. Pay closer attention to the instructions in your owners manual. Always double check your cam timing with what is recommended in the manual. Do not start your bike without turning the motor over by hand first. If you feel it is unusually hard to turn over or it will not turn over, you probably are off on your cam timing. Once again, do not try and start the bike. Go back and retime your cams.
Posted on Nov 26, 2008
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I will come back to you with the method for adjusting this.
If you set the power valve to open at a higher rpm or restrict the vavle from opening to its maximum then your problem will be solved.
If you do the latter though you will definately lose your power at high rpm.
Posted on Aug 04, 2009
Tips for a great answer:
Sep 22, 2018 | 2012 Suzuki RM-Z 250
Sep 06, 2018 | 2003 Suzuki RM 250
Jul 13, 2018 | 2004 Suzuki RM-Z 250
Jul 12, 2018 | 2003 Suzuki RM 250
Dec 13, 2017 | Suzuki RM 250 Motorcycles
Apr 15, 2016 | Motorcycles
Aug 05, 2009 | 2004 Suzuki RM-Z 250
Aug 04, 2009 | 2003 Suzuki RM 125
Jan 11, 2009 | 2004 Suzuki RM-Z 250
2,112 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: