1993 Wrangler 4.0 Randomly My clutch pedal will not go in.

Can't push clutch pedal in - JeepForum.com

www.jeepforum.com > ... > TJ Wrangler Technical Forum

Dec 11, 2010 - 7 posts - ‎3 authors
Driving home last night and the clutch pedal falls to the floor. ... Forums > TJWrangler Technical Forum > Can't push clutch pedal in ... Comes back up but then Ican't push it back in at all, even trying to stand on it, won't budge. Clutch locking up?
10 posts
Jul 30, 2011
Clutch Pedal Frozen Need tech help
10 posts
Sep 8, 2009
Clutch pedal stuck in the up position.
6 posts
Jul 26, 2009
Any more to clutch adjustment?
10 posts
Nov 28, 2008
More results from www.jeepforum.com

1998 Wrangler Sahara - Won't go into gear! Help please! - Jeep ...

www.wranglerforum.com/.../1998-wrangler-sahara-wont-go-into-gear-h...

Oct 5, 2010 - 22 posts - ‎7 authors
With the engine off, i can push the clutch in, and shift through all the gears ... to move - the clutch isn't disengaged even with the pedal fully depressed. .... Also, trying to bleed the system, can't find the bleeder screw. .... 1991 Jeep Wrangler Stuck In Gear? jeffasel, YJ Tech Forum, 5, 10-19-2010 09:42 AM. Getting difficult to push clutch pedal down, HELP
20 posts
Jun 17, 2011
How to bleed my clutch Be spacific.
11 posts
Feb 26, 2011
Clutch Problem?
30 posts
Jun 22, 2010
My Clutch Problems and How I Resolved Them
8 posts
Jan 28, 2009
More results from www.wranglerforum.com

ah.
how to reassemble the 93 jeep wrangler steering column?
someone else took it a part?
read the FSM. free.
YJ JEEP
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

do you mean it wont go into gear ? if so what gears ? it could be the clutch going out , if the pedal is soft or easy to push down than it probably needs a clutch. next time it wont go into gear try pumping the clutch or putting it from 2nd to 1st or what ever gear it has problems with

There should be a clip or a pin with a c-clip to hold the rod on the clutch pedal.

thrust bearings are bad and the flywheel is moving out of range of the crankshaft sensor, or the crankshaft sensor is sitting too close to the flywheel.

You should have a switch on the clutch pedal under the dash. easy to test,,,just jump across it and see if it starts (only with trans in neutral and your foot on the clutch because it can start in gear when jumped) You also have a relay in the power distribution center and a fuse as well. Relay test is simple...most of the relays are the same so just swap positions. You should also check to make sure power is getting to the starter...12v at main connection and 12v at the small connection with the key turned to the start position (again in neutral and at least have the brake on) If you have power at the starter, likely it has failed. Don't forget...ignition switch needs to be working as well.

I would really try to get the same year and motor as you have. There is some much that often changes from year to year, and engine to engine.

sounds like you are working on a car FSM free?
why do that?
95 YJ
early wrangler
i have 95 yj fsm and 93, the 93-95 are a year class range.
very simular.
here is a free 93 fsm with full schematics in chapter 8w
wiring chapter, clik
pdf 76 is page YJ 19 actual
and as you can see its cave man simple 2 wires.
minus to ECU ignitor driver. transistor (inside ecu)
and
+ goes to
a142 sheet 5 (pdf 62)

im not sure what part A<B<C is, a fuseable link, is my guess
and is blown. but that be a bingo spot for sure.
the full manual is there.
see spark chapter.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

posted over 100 times, this link, its not new.

yes it could be also check the fluid level!

possibly hydraulic clutch fluid? i have a 2002, not sure if the 93 has hydraulic clutch fluid but you might just want to check it to be safe good luck