I just bought this bike and I coluld not get it to go above 60 mph. I adjusted the float height and still could not get it to go above 60. I noticed the float valves were worn so I replaced them with stock valves from the dealership. Now it will idle but as soon as I give it a little gas it dies. I have thougherly cleaned the carbs several times even blown them out with air, but same thing only idle and give it gas it dies. It doesnt do anything like sputter or anything just dies. Any help would be greatly appreciated as I am getting strapped for cash and not having my bike is costing me a fortune in gas while im driving my car.
Probably you did not need to replace those, are both cylinders running?
was the motorcycle sitting for any length of time?
make sure the carb low speed jets are clear use carb cleaner the can with the with the tube and make sure the low speed jet will flow the fuid through it. if its clogged take a strand of copper wire and clear them.
SOURCE: raptor 660 idles but no throtle response
Turn off the gas and remove the water trap bowl at the bottom of the petcock, (gas valve). Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ). Get a set of the stock NGK spark plugs your bike came with. Check for spark on each cylinder before installing the plugs.
Now go to the idle and air screws on the outside of each of the carbs. IMPORTANT > > GENTLY turn both screws all the way in until they LIGHTLY seat. Now turn the screws EXACTLY one and one half turns outward.
SYNCHRONIZE THE CARBS
Remove the air filter and rubber fittings to allow you to see into the throat of both carbs. You may need a mirror to see inside. You need to be able to see the slides go up and down when you twist the throttle. Now turn the fitting where the cable goes into each carb such that there is just a bit of slack in the cable, 1/16" is plenty. Lock ONE of the cable adjusters down tight. All further adjustments will be made on the other carb.
With the motor turned off twist the throttle very slowly while looking at the slides. Both slides need to begin lifting at the exact same moment. If the slides don't raise at the exact same time then slowly twist the throttle until the locked adjuster slide just barely starts to move. Hold the throttle still and turn the adjuster on the other carb so that the slide on that carb just barely starts to move also. Now recheck the slide movement timing. Do this process until the slides on both carbs begin to raise at the EXACT same moment. Lock down the loose adjuster and re-check the slides.
BALANCE THE CARBS
Turn the throttle screw on the LEFT carb one half turn inward. Now start the engine and get it warmed up. With the engine running, remove the RIGHT spark plug wire. Adjust the idle speed on the left carb to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.
Now turn the throttle screw on the RIGHT carb one half turn inward. Restart and rev the engine. Next, remove the LEFT spark plug wire. Adjust the idle speed on the right carb to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.
Turn the idle screw on each carb EXACTLY ONE QUARTER turn outward and restart the engine. The engine will be probably be idling very fast. Adjust both the idle screws equally from this point to get to the desired idle speed. Congratulations, you have just synchronized and balanced your carbs.
PLEASE RATE THIS SOLUTION. Thanks!
SOURCE: Yamaha 06' V-star 650 idle prolbem!
Fuel filter is located near the fuel shutoff valve within three inches. It is inline between the shutoff valve and the fuel pump (towards tank).
The fuel circuit is: Tank/Fuel Pump/Fuel Filter/Fuel Shut-off Valve/Carbs.
You first step is to check for fuel delivery to the filter. Make sure the bike is cool and no iginition sources are nearby. Disconnect the inlet line at the filter and turn key on and crank engine (to trigger fuel pump.) Do not try and start at this time (choke off).
If fuel is adequate to the filter, check the filter by blowing through it, it should easily pass air. Replace filter if questionable.
Next reconnect the fuel lines and remove float bowl drain plugs in the back of the carbs (2 per carb). If with key on and cranking fuel pours out of these ports then you probably have clogged fuel jets. If not then the float bowl needles / pipes could be plugged with varnish from dried fuel. You can try spraying carb cleaner into the fuel inlet to clear the varnish and then retest. Careful not to spray carb cleaner on yourself (wrap straw with a rag).
If you have good fuel flow to the carbs and bowls you probably have varnish plugging the jets. You should remove the carbs and clean them thoroughly.
Hope this helps,
Kal
SOURCE: won't idle steadily
Check the rubber boot that joins the carby to the engine to often have seen the hose clamps over tightened therefore creating a split in the rubber letting to much air in giving the rough idle eventually you wont be able to start it at all (have a good thorough look inside an outside of boot doesnt take much)
5,778 views
Usually answered in minutes!
both cylinders are running, and the bike hasnt been sitting for over a couple of days. Ive cleaned the carbs with carb cleaner and compressed air. all points where i put carb cleaner it comes out some where else. Im at a total loss.
×