2006 kymco 250 quad... failed to start this morning for the first time ever,pressed the ignition switch and it was if the battery was dead..then tried it again and there is nothing...no sound,no clicking...nothing!!!! lights are still strong etc..
was the solenid....thankyou very much..was the solenid....thankyou very much..
AnonymousApr 30, 2009
when i start the machine and drive whatever howlong, as soon as i switch it off, for exemple when i stop somehwere and switch the machine off, and when i try to start it again, nothing will happen, even on the board there will be no lights at all, but when i wait 2 hours till 3 h, everything is here again, when i switch on, on the board lights are on, and i can start the machine normally and i can drive howlong i want, till i twitch off, and the operation starts again, i can do nothing just after the 2 .3 hours are passed. what can this be ? could you please help me, knowing that i am begginger with the Quad, Kymco 250 sport. thanks in advance.when i start the machine and drive whatever howlong, as soon as i switch it off, for exemple when i stop somehwere and switch the machine off, and when i try to start it again, nothing will happen, even on the board there will be no lights at all, but when i wait 2 hours till 3 h, everything is here again, when i switch on, on the board lights are on, and i can start the machine normally and i can drive howlong i want, till i twitch off, and the operation starts again, i can do nothing just after the 2 .3 hours are passed. what can this be ? could you please help me, knowing that i am begginger with the Quad, Kymco 250 sport. thanks in advance.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Geez dont keep spending money if your not sure. It sounds like your starter is not throwing in far enough to engage with the ring gear. Please do your hip pocket a favor and get an auto technician to check it before buying a new starter as well. You can also remove the starter and check the gear to make sure its not worn as some are plastic.
Remove battery terminals and clean both posts and terminals with sandpaper until you see shiny metal. The black coating is lead sulphate which has a high resistance to current flow both into and out of the battery. Have a load test done on the battery also as a cell may have dies while you were riding and the bike was running on the alternator.
Although these answers are correct many are not probably. Valves are not going to go out of adjustment during the off season etc. You need to simplify it. You need gas, fire (spark) and air for a motor to run. Usually it will be the fact that the carb was not ran dry at the end of the season and fuel stabilizer was not used so the carb is dirty. You can pull you plug and see if it is wet with gas or try some engine starting fluid sprayed in the carb. Dry plug means no gas, no run with starting fluid mean no spark. Make sure fuel is on and the obvious has already been done. 90% chance dirty carb.
kymco 500 has no air temp sensor,ecu reads water temp for coldstart enrickment.a new sender wont fix it ether,sender needs to read 10 degrees warmer to start
was the solenid....thankyou very much..
when i start the machine and drive whatever howlong, as soon as i switch it off, for exemple when i stop somehwere and switch the machine off, and when i try to start it again, nothing will happen, even on the board there will be no lights at all, but when i wait 2 hours till 3 h, everything is here again, when i switch on, on the board lights are on, and i can start the machine normally and i can drive howlong i want, till i twitch off, and the operation starts again, i can do nothing just after the 2 .3 hours are passed. what can this be ? could you please help me, knowing that i am begginger with the Quad, Kymco 250 sport. thanks in advance.
×