Remove the swingarm 2008 Qlink Commuter 250

https://mechanics.stackexchange.com/questions/33293/cvt-belt-repair-problem-on-my-08-qlink-legacy-250cc-scooter

250CC Automatic Motorcycle Carburetor CFMOTO V3 V5 ...

eBay https://www.ebay.ca > itm

250CC Automatic Motorcycle Carburetor CFMOTO V3 V5 Qlink Legacy Sapero 250 ... Decent replacement, with an OK fit, for the original Mule 550 master cylinder.
$133.15 · ‎ In stock

CFMOTO Qlink 250 Automatic Motorcycle Scooter ... - eBay

eBay https://www.ebay.ca > itm

CFMOTO Qlink 250 Automatic Motorcycle Scooter Carburetor V3 V5 Legacy Sapero Com ; Quantity. 12 sold. More than 10 available ; Item Number. 183200768184.
$146.66 · ‎ In stock

CFMOTO Qlink Carburetor for V3 V5 Legacy 250 Sapero

Whygostock.com https://www.whygostock.com > cfmoto-qlink-250-aut...

Sep 5, 2019 - CFMOTO Qlink 250 Automatic Motorcycle Scooter Carburetor V3 V5 Legacy Sapero Commuter Fashion Baron. MSRP: Now: $119.99.
Rating: 4 · ‎ 1 review · ‎ US$119.99 · ‎ In stock

Typically most gear drive motorcycles use the same type of system. There will be a small bolt either 8mm or 10mm or a Phillips head . That will be at the bottom of the gear case just below the rear axle. Remove the bolt and let it drain. There should be a smaller screw or bolt of some sort above the axle. That will be the " weep " hole. Once you finish emptying the gear box. You re install the drain plug and fill the gear box through the weep hole. You fill it til it starts to come out past the threads. That is the correct fluid amount. Re install the weep hole plug and you're good to go.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_5bac37c3cb991fdb

Check battery, battery fuses, wire condition of the wires going from battery to the switch and check the switch.

If you need further help, reach me via phone at https://www.6ya.com/expert/lloyd_4256582adacd68ee

2 cycle needs oil mix 4 cycle does not

http://store.qlinkmotor.com/products/productdetail/SM_CM250/part_number=Service+Manual+-+Commuter+250/1658.0.1.1.55625.55645.0.0.0?pp=8&

Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

Try these:

KTM Torque settings

1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
17. Engine brace Engine brace 33Nm 24ft lbs
18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
19. Spoke nipple Spokes 5Nm 4ft lbs
20. Other Screws on chassis M6 10Nm 7ft lbs
21. M8 25Nm 19ft lbs
22. M10 45Nm 33ft lbs
23. Other collar nuts on chassis M6 15Nm 11ft lbs
24. M8 30Nm 22ft lbs
25. M10 50Nm 37ft lbs
26. Front Sprocket 44ft lbs

TF