2005 Harley Davidson FLSTN- FLSTNI Softail Deluxe Logo
B
Bob myers Posted on Dec 11, 2013
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

How to retrieve fault codes - 2005 Harley Davidson FLSTN- FLSTNI Softail Deluxe

Answer This Question

1 Answer

Strech

Strech

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Harley Davidson Master 1,562 Answers
  • Posted on Dec 23, 2013
Strech
Harley Davidson Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Nov 15, 2012
Answers
1562
Questions
0
Helped
484261
Points
4382

1- Turn IGNITION SWITCH to OFF & Run/Stop switch is to Run.

2- Push odometer reset button in & hold.

3- While holding odometer reset button, turn IGNITION SWITCH to Ignition and release odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word "diag" should then appear.

4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.

5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module[Carbureted])
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer

6 - To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC's the code will be displayed or the word "none" will appear if there are no DTC's. Push the odometer reset button again to view additional codes if they exist.

7 - Record the codes.

8 - If DTC's are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button (longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC's again by repeating steps 1 to 9. If the code is current it will reappear.

9 - Press and release the odometer reset button to continue to the next module.

10 - Turn Ignition switch to OFF.

On models not equipped with a tachometer "No Rsp" will appear when the TACHOMETER identifier is selected.

"No Rsp" (no response) will also appear if the run/off switch is in the off position when doing this procedure.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

How do I retrieve fault codes on Sportsman 570
you can retrieve the code with the help of the manual which you can get the manual from the given link http://toolsnyou.com/ this link is very safe and helpful i had tried it before
Read full answer
Aug 25, 2017 • Cars & Trucks
0helpful
1answer

2007malibu cut off while driving
There are many reasons of this to happen and most of them will set a fault code in the memory of the powertrain control module, so you must have the system scanned and retrieve those fault codes to begin to diagnose this problem.
Read full answer
Jul 08, 2016 • Cars & Trucks
0helpful
1answer

Nissan F1 fault code, what does it mean?
"F1" was the fault code retrieved from WHAT by the auto shop?
Read full answer
Jan 05, 2012 • Cars & Trucks
0helpful
1answer

Nissan F1 fault code, what does it mean?
Nissan WHAT??? What year? What model? What engine size? Which control module was this code retrieved from?
Read full answer
Jan 05, 2012 • Cars & Trucks
0answers

I have a 04 Ford Freestar that will mis between 45 and 55 mph with no check engine light. has anyone had this problem
Read full answer
Be the first to answer Dec 28, 2011 • 2004 Ford Freestar
2helpful
1answer

D4 light on no matter what gear i'm in. 95 Honda Accord LX 4-cylinder. Already replaced solinoid, speedometer, fan,
The D4 light is coming on to tell you that there is one or more fault codes set in your transmission control module. The only way to retrieve codes on the 1995 models is to read "Flash Codes" output by the D4 light. (See instructions below)

RETRIEVING FLASH CODES USING THE D4 LIGHT
If fault codes are present, the D4 light will "blink" when the ignition is turned to the RUN position and will remain on at all times when the engine is running.
To retrieve the flash codes, turn the ignition switch off.
Install a jumper wire between the service check connector terminals.
The service check connector is a gray, 2-pin connector located on the PCM/TCM cover under the passenger side of the instrument panel. (See picture below)

CAUTION: DO NOT use the 3-pin located next to the service check connector.

Installing the jumper will place the PCM/TCM in diagnostic test mode.
Turn the ignition to the RUN position. Codes will be output by blinking the D4 light.
Note the number of blinks from the D4 light. A short blink indicates a single digit flash code. A long blink equals 10 short blinks. For instance one short blink indicates code 1. One long blink and four short blinks indicates code 14. If there is more than one fault code, they will be output one at a time from the lowest numbered code to the highest numbered code. It is recommended that you read the code or codes several times to make sure that you are reading it correctly.

Once you have retrieved the fault code(s) re-post your question and include the information for what codes you have and someone can then help you locate the cause of the problem.
Read full answer
May 22, 2011 • Honda Accord Cars & Trucks
2helpful
1answer

Is there an ALDL port on a legend ...to plug in a scan tool
There is a connector but it is not like the connector used in the newer 1996 OBD2 cars, your year uses OBD1, here is how you check for codes in this car.

Acura OBD1 Codes Retrieval
Acura vehicles 1986-95 obd1 code retrieval
There are a few different ways to retrieve the codes for "check engine light" for Acura vehicles. One method is to use a led light (sometimes 2 led lights) on the computer or controller box itself. If it has 2 led lights, the color is red and amber. The red is used for flashing the codes whereas the amber is used for adjustment. If you have only a single led light indicator, then that is used for flashing the code.
The controller box can be found by lifting the carpet of the passenger side front foot well or floorboard. You can see the led lights without removing the controller. On other models, you can find the controller under the driver or passenger front seat.
The second way to get the code is using a jumper wire on the diagnostic connector located on the kick panel at the front passenger side. You then watch the codes being flashed at the dash panel after you turn the key on. To read the code being flashed is easy. Example: Code 23 is 2 long flashes followed by 3 short flashes. A longer pause separates the next code that follows.
Here are Acura vehicles 1986-95 general codes:
Code 0 Electronic control unit (ecu)
Code 1 02 (oxygen) sensor
Code 3 and 5 map sensor
Code 4 Crank angle sensor
Code 6 Coolant temperature sensor
Code 7 Throttle angle sensor
Code 8 Crank angle sensor (TDC)
Code 9 Crank angle sensor (CLY)
Code 10 Intake air temperature sensor
Code 12 EGR system fault
Code 13 Atmospheric pressure sensor
Code 14 Electronic air control valve
Code 15 Ignition output signal
Code 16 Fuel injector fault
Code 17 Vehicle speed sensor
Code 21 Spool solenoid valve
Code 22 Valve timing oil pressure switch fault
Code 23 Knock sensor
Code 41 Oxygen sensor heater fault
Code 43 Fuel supply system
Read full answer
Nov 30, 2010 • 1990 Acura Legend
0helpful
1answer

How do I retrieve fault codes from a 1995 Geo Tracker?
On a 1995 model you should have OBD II codes. Which means you can buy a scanner that plugs in to a clip usually located under driver side dash. If you don't want to buy the scan tool Advance Auto or Auto zone can read these codes for you while you visit the store and is free.
Read full answer
May 18, 2010 • Cars & Trucks
0helpful
1answer

SERVICE ENGINE LIGHT ON
There is a problem with the emissions system, an the ECU has set a fault code. The ECU will have to be scanned. The fault code you retrieve will help in determining what the problem is.
Read full answer
Aug 02, 2009 • 1997 Saturn SW
1helpful
1answer

My Isuzu Rodeo 1997 Check engine light is on There is no Isuzu technician in my area''
You have fault codes stored in your vehicles computer. Any local mechanic with a diagnostic machine can retrieve these codes that will diagnose your electrical component issue. To retrieve codes - $50 to $75.
Read full answer
Jun 08, 2009 • 1997 Isuzu Rodeo
Not finding what you are looking for?

View Most Popular

2005 FLSTN- FLSTNI Softail Deluxe

  • Motorcycles

Related Question

How do I retrieve fault codes on Sportsman 570

  • Cars & Trucks

Related Topics

290 views

Ask a Question

Usually answered in minutes!

Popular Questions

What is the spark plug

Harley Davidson FLSTN- FLSTNI...

Removing seat for batter accese

2005 Harley Davidson FLSTN- FLSTNI...

Harley speedometer stopped working

2005 Harley Davidson FLSTN- FLSTNI...

What is the correct air

2005 Harley Davidson FLSTN- FLSTNI...

Lost my FOB I have a new one but I cant turn the

2005 Harley Davidson FLSTN- FLSTNI...

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...