2008 gsxr 600 F1 code keeps flashing wont start

I HAVE A 2005 GSXR 750 AND WHEN IM AT HIGH RPM THE BIKE SHUTS OFF. DOES THIS HAVE ANYTHING TO DO WITH THE FI CODE BLINKING? BUT THERE ARE DAYS WHEN IT RIDES FINE....WIERD

http://www.gsxr.com/showthread.php?t=1234&highlight=codes i know th
is link is for gixxers but shouldnt be a massive difference and should give a rough idea hope it helps

When the red light comes on, eg (F1) use these fault codes to find your problem. To extract the codes from the computer system, there is a two pinned connector hanging out of the wiring harness, on the left hand rear of the bike, (say above the pillion foot peg under rear trim. Be sure not to confuse the other connector used by the Suzuki Workshop Mechanics, as this has four or five wires to the connector) After locating the one with only two wires at the back, use a split pin or paper clip to bridge the two wires togeather and turn the ignition to the ON position. You should now be able to read the code on the console. The fault codes are as follows,,
**** GSXR Fuel Injection (FI) Code List:*****
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL

if you can access the ignition switch wires, move the protective covering down the wires and take straight pin and push through the large red and brown wires. it wont shock you but dont short them to ground either, they are powered. now your lites and gauges should work. if they do then your ign sw. is bad.

White smoke is unburnt oil so it may be been overfilled or a vavle seal has popped out

there is a plug under your seat with 2 wires that you need to short out. The fI code is a dealer code like a check engine light on your car. You need the actual problem code. turn the bike on and keep it running short out the two wires in a white harness under your seat and then the f1 will change to a C## code.
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

Also a good place to look to make sure you have the correct wires is :
http://www.gixxer.com/forums/showthread.php?t=192222
it is a great site to belong to for future issues or just for fun

The display is really FI as in Fuel Injection. The fuel injection computer has sensed a fault in the Injection system. You will need to ride the bike to a dealer and have them read the fault codes. It is probably just something minor. Major faults will not allow the bike to run. You will not hurt the bike if you ride it.

Can I get a “very helpful” rating on this answer?

The FI light is letting you know there is a problem with the Fuel Injection system on the bike. You will most likely need to take it to the dealer and have them diagnose it with their computer. You can check your fuses and make sure they are intact, but most likely dealership problem.