No lights or electrics - 2007 TGB R50X

Question edited for clarity and spelling errors.
Question moved from Cars and Trucks category.

contact the maker direct

https://www.google.com/search?q=poweroll+2+Electric+Cigarette+Machine+light+flashes+a+blue+light

..

LED (light emitting diode) lights use much less electricity and put off much less heat than the old incandescent bulbs. For example, a 9 Watt LED bulb can put out as much light as a 75 Watt incandescent bulb.

blinking green red light Electric Kettles Questions & Answers ...

www.fixya.com > Forum > Tags > blinking green red light

Electric Kettles blinking green red light questions and answers. Ask your blinking ...the kettle lights up but won't heat up, just bought it, the on switch shows red, but it isnot working...what to do? ... Chef's Choice 677 Cordless Electric Kettle.

red icon blinking Electric Kettles Questions & Answers - Fixya

www.fixya.com > Forum > Tags > red icon blinking

Electric Kettles red icon blinking questions and answers. Ask your red icon ... Light will not stop flashing Even after descaling and cleaning thoroughly the red lightflashes. Any ideas? ... "On" switch blinks, kettle won't heat Our 4-week old kettle juststopped working. When we ... Chef's Choice 677 Cordless Electric Kettle.

first off ,,,electric ovens dont have pilot lights ,,,its electric..the burner is electric....now ,,on a gas oven thats different..first remover the old one,,,then replace with new following reverse directions from removing the old one ....

The electrical portion of the ignition switch is at fault.

check all your fuses in engine compartment and under dashboard engine check light comes on every 3000 miles for oil change reminder

Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:

1. Disconnect battery negative cable.
2. Disconnect electrical connector. Rear Combination Light
   
   
3. Remove 2 screws and 2 nuts and remove light assembly.

To Install:

1. Install light assembly and 2 screws and 2 nuts.
2. Connect electrical connector.
3. Connect battery negative cable.

5 Door To Remove:

1. Disconnect battery negative cable.
2. Disconnect electrical connector. Rear combination light
   
   
3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
   Use care to not damage gasket.
   
4. Pull rear combination light from vehicle.

To Install:

1. Install rear combination light and 2 screws.
2. Install 2 screws.
3. Connect electrical connector.
4. Connect battery negative cable.

2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp

1. Disconnect battery negative cable.
2. Remove 2 screws and cover inside trunk.
3. Remove 4 nuts and disconnect electrical connector (A).
4. Remove rear combination lamp.

To Install:
Turn Signal Lamp

1. Install rear combination lamp.
2. Install 4 nuts and connect electrical connector (A).
3. Install cover inside trunk and install 2 screws.
4. Connect battery negative cable.

check the dome light fuse or electric lock fuse, sounds like they might be one in the same.

one hour job. find bulb part number in bulb chart in owner manual.

go here for villager help.

http://groups.yahoo.com/group/villagerquest/

Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal

1. Disconnect the battery ground cable (14301).
   

1. Block the wheels (1007) to prevent the vehicle from moving.
   

1. Turn the ignition switch (11572) to the OFF position.
   

1. Shift the transmission range (TR) selector to MANUAL LOW (1).
   

1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
   

1. Remove the two instrument panel finish panel screws.
   

1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
   

1. Disconnect the rear windshield wiper/washer switch electrical connector.
   

1. Disconnect the heated back window and light switch electrical connector.
   

1. Disconnect the emergency warning switch electrical connector.
   

1. Disconnect the SECURITY indicator light electrical connector.
   

1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
   

1. Disconnect the headlamp switch electrical connector.
   

1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
   

1. Remove the instrument panel finish panel with the switches attached.
   

-------------------------------------------------------------------------------------------------
Instrument Cluster
Removal

1. Disconnect the battery ground cable (14301).
   

1. Block the wheels (1007) to prevent the vehicle from moving.
   

1. Turn the ignition switch (11572) to the OFF position.
   

1. Shift the transmission range (TR) selector to MANUAL LOW (1).
   

1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
   

1. Remove the two instrument panel finish panel screws.
   

1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
   

1. Disconnect the rear windshield wiper/washer switch electrical connector.
   

1. Disconnect the heated back window and light switch electrical connector.
   

1. Disconnect the emergency warning switch electrical connector.
   

1. Disconnect the SECURITY indicator light electrical connector.
   

1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
   

1. Disconnect the headlamp switch electrical connector.
   

1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
   

1. Remove the instrument panel finish panel with the switches attached.
   

1. Remove the four instrument cluster screws.
   
2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).
   

less then TV.