Question about 2013 Kymco Agility 50

2 Answers

Why won't my Kymco start? Has power to everything and the relay swifch clicks, that's all it will do

Posted by Anonymous on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kymco Master
  • 9,098 Answers

KYMCO Agility 50 Scooter Online Service Manual ...

https://www.cyclepedia.com/...manuals/kymco...scooter...repair-manuals/...
The CYCLEPEDIA PRESS LLC KYMCO Agility 50 Scooter online service manualfeatures detailed, full-color photographs and wiring diagrams, complete ...

Posted on Aug 11, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 25 Answers

Check fuel level.

Posted on Sep 16, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Kymco Xciting 500 I will not turn over


Hi, Dean before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
500 RI won start
Scooter Troubleshooting Scooter won start All about Scooters KYMCO XCITING 500 Service Manual
Kymco Parts Online Kymco Parts monster
https://www.kymcousa.com/admin/dealeronly/ownerman/onroad/Xciting250-500_pre2008.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 23, 2018 | 2006 Kymco Xciting 500 I

1 Answer

Kymco downtown 300i oil light stay on and won't start


Hi, Michael and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day
Downtown 300i Won Turn Over
http://meiguohosting.com/How-to-fix-start-problem-for-your-2011-Kymco-Downtown-300i
KYMCO People GT 300i Service Manual
Downtown 300i Kymco Scooter Parts Racing Planet USA
KYMCO downtown 300i Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Feb 26, 2017 | 2013 Kymco Downtown 300i

1 Answer

Why won't it run


have you checked the relay between the battery and the starter?
i had a ltd 2 that suddenly refused to start after trying everything else it turned out to be a little black box(relay) on the fender well between battery and everything else!

May 08, 2013 | Cars & Trucks

1 Answer

I have a kymco agility 50 and it won't start. It has no power what so ever, the starter won't turn over and the break light won't light when I pull the break. I checked the kill switch.


Check with a multi tester for voltage coming through the ignition switch lead wires + to switch wire - to ground you shoul get 12volt or higher, with the switch off you should have one live (feed from battery ), on you should have 2 or 3 in and out feed (possibly 2 out one for ignition one for light curuit), or disconnect the switch and check for continuity (12v battery wire and a bulb if you dont have a multi tester between each pin on the switch plug when turned on you should get a curcuit when on.

Jan 27, 2012 | 2006 Kymco Agility 50

1 Answer

The car won't start; lights, ac, radio etc come on but car won't turn over or even click; checked battery cables; put different battery in; still won't start


Check the starter and the starter relay or fuse. A client of mines car was doing the same thing, it ended up being two issues, the starter not working anymore, and a relay that was bad. If I am not mistaken everything should be labeled in the fuse box under the hood and will tell you where the fuse/ relay is for your vehicle

Jun 12, 2011 | 2001 Ford Escort ZX2

1 Answer

'04 Kymco Venox won't start. Bought it a few months ago from someone w. about 20,000 miles on it. Always runs good/never had a problem w. it 'til yesterday. Ran outta gas on the road...put more...


Hi Mrcherry99, for this situation I would call my local dealer or reputable shop's service department and inquire about any possible quick fix. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if possible, and give you a written estimate of repairs and answer any specific questions you may have about your issue. Good luck and have a nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 18, 2011 | 2005 Kymco Venox 250

1 Answer

I Have a 94 cherokee country with a 56028297 ecu,it has no power at the grey wire at the ecu,it does flash sometimes and I can hear the relay work sometimes. I can bypass the fuel pump relay circuit and...


If you hear relays clicking sometimes and the jeep won't start, at those times, is the check engine light illuminated on the dash, or not? If no check engine light is on the dash, at times when the jeep won't start, your ecu is in need of repairs. The ecu sends power to the ignition and fuel relays and when the ecu starts to malfunction, the relays usually start clicking.

May 11, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

2002 Kymco Hipster 125 will not turn over


Hi, Anonymous before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike won start any ideas
What Do Check When My Motorcycle Won Start Honda Shadow Forums Shadow...
Kymco Hipster 125 150 Motorcycle Complete Workshop Service Repair Manual... $20
Genuine Kymco spare parts
Manuals Kymco

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 11, 2017 | 2002 Kymco Hipster 125

Not finding what you are looking for?
2013 Kymco Agility 50 Logo

684 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...