Do check horn switch if it is ok test with a mutitester set it ohms x1 check terminals if there is continuity nxt adjust the bolt screw at the back of the horn and try press horn switch. 2. check the bulb f the filament is ok and the brake switch. 3.check flasher relay if it is still good. tips tap x to 12v then L to bulb center contact body of the bulb connect to ground if not working replace new one.
SOURCE: how do you change the battery on a 2005 dyna wide
I have a '94 model FXDWG and I don't know if Harley has changed anything or not but here's how I get mine out.
Remove the seat first. Then the battery cover will come off the top and around the battery. Look on the left side of the battery tray that there are two bolts going into the frame. Loosen these bolts. Now back up on top of the frame behind the battery, there is a bolt that raises and lowers the battery tray. Lower the battery tray. Disconnect battery cables (negative first always). Remove battery.
Hope this helps.
SOURCE: Will a 2005 dyna wide glide gas tank fit on a 1993
no...... a 2005 tank will fit on models only back to 1996
SOURCE: where is the fuse located for the horn on a harley
Harley has been moving the fuse panel around since 2000. On the older Wide Glides, it was behind the "electical box" cover on the left side of the bike. That's the cover just to the rear of the coil cover. But, you might want to take the seat off and look there as well.
Good Luck
Steve
SOURCE: how do i install the fuel regulator on my H-D 2005
BELOW IS A COPY OF THE FUEL PUMP INSTRUCTIONS FROM THE MANUAL FOR A 2005 DYNA WIDE GLIDE FOLLOW THESE INSTRUCTIONS AS THE FUEL REGULATOR IS IN THE FUEL PUMP FUEL PUMP 9.14 GENERAL 1WARNING Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. CAUTION Do not replace the special teflon coated fuel pump wiring with ordinary bulk wire. Ordinary insulation materials may deteriorate when in contact with gasoline. NOTE Carefully inspect hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even a small hole can cause a reduction in fuel pressure. Refer to the DYNA Models Electrical Diagnostic Manual for information on the function and testing of the fuel pump. REMOVAL 1WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 1. Purge the fuel supply line of high pressure gasoline. a. Disconnect the fuel pump fuse located in the electrical caddy. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect negative battery cable. 3. Remove instrument console 1WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and disposeof rags in a suitable manner. (00259a) 5. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. Cut clamp from one end of crossover hose. Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 6. Unplug fuel pump and sender connector 7. Remove vent hose . 8. Remove top plate screws and discard. 9. On FXDL and FXDWG models, rotate top plate until vent tube clears fuel tank. 10. Depress tab and remove fuel pump/ sender wiring from top plate. Remove top plate. 11. Depress tabs and remove fuel line from fuel pump assembly. 12. Remove fuel gauge wiring harness from clip. 13. Disconnect fuel pump connector. 14. Lift fuel pump assembly tab. Push assembly towards front of vehicle to disengage from fuel tank. 15. Rotate fuel pump assembly clockwise and upward to remove fuel pump assembly from fuel tank. DISASSEMBLY/ASSEMBLY Fuel Filter 1. Depress tab and remove filter retainer clip. 2. Separate fuel pump body from end cap. 3. Remove o-ring. 4. Remove fuel filter. 5. Install new fuel filter. 6. Install new o-ring. 7. Place end cap on fuel pump body. 8. Install fuel filter retainer clip. Regulator 1. Remove wire terminal. 2. Disengage clip from regulator. 3. Remove regulator from pump assembly. 4. Install new o-ring on new regulator. 5. Install regulator into pump assembly. 6. Install clip over regulator. 7. Replace wire terminal. Sorry I couldn't transfer pictures in here. If you have anymore questions please feel free to email me at [email protected]
62 views
Usually answered in minutes!
×