Why does my right cylinder pop out the exhaust on my 2001 Suzuki 1400 intruder?

SOURCE: Clutch bleed on a Suzuki 1400 Intruder 2000

One the left-hand side of the bike (facing forward), there is cover plate just ahead of the drive shaft. Remove that cover (mine has 8mm bolts). The bleeder valve is under this cover. Go to an auto parts store and get a "one man bleeder kit" or if you have some plastic tubing that will fit over the valve, you can use that and a clean jar. Follow the instructions on the bleeder kit, or if you're using the jar and tubing, fill the jar about a quarter of the way with break fluid (use DOT4, but never DOT5!). Take the cover off the master cylinder up at the handlebars, place the tube over the end of the bleed valve (after loosening it a turn or two. Place the other end of the tube down in the break fluid in the jar. Work the clutch lever until you stop getting bubbles in the jar. Be sure to keep the fluid level up in the reservoir. Tighten the bleeder valve, remove the tubing, top off the fluid and replace the covers.

Be careful not to get brake fluid on anything. It will eat paint and mess up other things.

SOURCE: backfiring and low compression in back cylinder

sounds if you have a burnt valve/s somewhere

SOURCE: My suzuki 1400 intruder back fires

dont play with the valves it is unecessary,you would be better off checking your exhaust system to make sure it has no leaks,if gas can get out,air can get in this mixes with the unburnt fuel in the pipe and the heat from the next exhast stroke ignites this mixture causing a backfire,or option two is to check that the carbs are not out of balance and are running the correct miture or air/fuel ratio,this can be done with a set of carb balancers and a little bit of time and knowhow..hope this helps

SOURCE: My suzuki intruder is missing backfiring on the

Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.

SOURCE: 2001 SUZUKI INTRUDER 1400 BEEN

The Bike Technicians Tactic

Phase1

An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician's tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities.

Engine Technicians Tactic

PHASE 2

A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.