Question about 2004 Yamaha DT 125 R

2 Answers

DT125 no electrics! non starter

Hello, my DT125 was stolen, got it back couple of wires cut.

Repaired wires put new batt on but get nothing when I turn the key in the ignition. No lights, no power at all. The bike bump starts and all the electrics work then, but I don't have a kick so I need to sort this out

Zero dash lights horn etc when key turned in ignition

all works once bumped

fuses maybe? starter gone?

thanks for reading! any help well appreciated


Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Master
  • 1,810 Answers

How about replacing the fuse by the battery it is a master fuse and thats what it sounds like
since all lights and bike runs after a bump it sounds like a master fuse problem
if not check your batterie ground it might be cut or loose

Posted on Aug 04, 2009

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Did u manage to sort it because i have the same problem??

Posted on Apr 26, 2015


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

98 chevy malibu my alt isnt charging new alt batt test good cut out the fuselink on starter the alt wire runs thru firewall If i run a wire straight to the batt it is putting out 19v any suggestions

Did you check the fuse in the under hood fuse box ? GEN / BATT fuse 10amp . Is your check engine light on ? This is a computer controlled charging system , it should have four wires connected to the alternator . 1 - the heavier wire on the back ,this comes fro the starter - the one with fusible link , you could have checked for battery voltage with voltmeter ! The three other wires in the connector are the orange one ,this comes from the GEN / BATT fuse an should have battery voltage ! The last two come from the PCM - engine computer . The gray wire is the turn on signal from the PCM an the Red wire is the control from PCM ! Charging System Wiring Diagram MOTOR Magazine Article MOTOR Information Systems

Aug 14, 2015 | Cars & Trucks

1 Answer

I have a 2001 Mazda tribute it won't turn over turn the key and nothing happens

have you got power to lights if so are they dim and cut out could be simple batt connection or starter motor,listen carefully when you turn key do you hear anything small "click" by any chance if so lift bonnet look for saddle of wires looks like 8/10 coloured wires all grouped together check the push in connectors maybe corroded open them clean them wd40 them and seal from future water getting into them I put plastic bag over the connector and electric tape round end hope this helps

Mar 13, 2015 | 2001 Mazda Tribute

2 Answers

Toro Wheel Horse 16-38 XL - 2001 - won't start

1. Check Fuses
2. Check Ground wire from batt to frame.
3. Check wires on the starter.

Nov 18, 2017 | Cars & Trucks

2 Answers

My bike will not turn over. When i push the electric start the starter solenoid just clicks.I tried jumping across the solenoid and still nothing, when i got the bike a few months ago I put a new battery...

pull the starter and check it by putting it on a testor or just hooking it to a good(known)battery. If it tests good then check/replace the starter switch and check wires to the switch.

Sep 08, 2011 | 1984 Honda CB 700 SC Nighthawk

1 Answer

1997 Ford E150 4.2L Start troubles

The transmission range sensor , park neutral safety switch . Is fuse #23 60 amp in the engine bay fuse block good ?

Mar 10, 2017 | 1984 Ford Econoline

1 Answer

Problem with a 2000 chevy blazer not starting

Have replaced starter, alternator , ignition wiring, neutral safety starter switch, still happens ??????? Do you know how to do automotive electrical testing ? Not guessing an replacing parts . Not starting ??? How ? when you turn the key to start does the starter motor engage an spin the engine ? Or when you turn the key to start nothing happens ? A no crank no start or a cranks no start . Plus you shoud learn how the system works before trying to diagnose .

Jun 18, 2017 | 2000 Chevrolet Blazer

1 Answer

I have a dodge ram b250 1994 needed a new batt went and bought one after i put it in the van is completely dead no lights no nothing so its not the batt checked all the cables even put the old batt in...

I have found that sometimes if the starter wire that is attached to the starter is loss it can cause you to have no electric power to anything. Hope this helps. Also Check all fuses inside and outside the vehicle. But first check the starter wires. They can be found going from the Hot post of the battery down to the starter. Hope this helps.

Dec 06, 2009 | Dodge Ram 250 Cars & Trucks

1 Answer

Car wont start oe even crank.

some cars have a problem when you change the car radio it can trigger the alarm system the alarm may think that car was being stollen and kicked in the immobiser which would turn off the starter motor which is giving the affect the batts flat,, plus a lot of the ford and vauxhalls when this happens it also shuts down the fuel pump, or ignition ,, if you have the key pad to lock and unlock car use this a couple of times this can reset the system . if not it may have to go to the main dealer to do a computor check to find fault and may be 10 mins to put right ,, matdav69

Apr 05, 2009 | 1999 Volkswagen Passat

1 Answer

No Electrical power

Check voltage at starter main terminal (12v) Check for good block ground. If you have replacement ends on batt cables, make sure the wire under each strap is clean & making good contact.

Mar 14, 2009 | Chevrolet Silverado 1500HD Cars & Trucks

1 Answer

Remove a starter form a 98 s-10

1. open hood
2. remove batt. cables
3.remove batt. cable on starter
starter is located lower pass. side of motor
(also might be a couple of other wires connected to the starter remove them as well & remember their locations).
4. remove two bolts that mount the starter to the trans. bell housing. and remove starter
5. install new starter and hook wires up with the batt. last.

Jan 12, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
2004 Yamaha DT 125 R Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Paul Ellermets

Level 1 Expert

6 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides