Question about Kymco Motorcycles
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: leaking gas from overflow hose
Double check the float needle seat. Often a piece of debris will lodge itself under the needle. Check your fuel tank/fuel valve for debris or damage to the strainer screen on the fuel valve.
Posted on Jun 29, 2010
From a Sym dealer, or from the carb manufacturer. If you look on the carb you will be able to see a makers name, you will also need the needle size for your bike.
Posted on Aug 24, 2013
SOURCE: PHM40 flooding
Hi, George if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly then stall, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and the battery needs to be replaced.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove and inspect your air cleaner paper elements that are not oil soaked can be cleaned with a soft brush and low pressure compressed air, oil soaked elements must be replaced. Gause mesh and foam elements can be cleaned by soaking them in a container big enough to completely cover them with a solution of 1 gallon of water and 1 oz. of Dawn dishwashing liquid for small and medium size elements, for monster size double the formula and let soak for at least one hour then rinse with warm water shake off excess and let air dry, "WARNING" do not use compressed air as this will embed micro-sized dirt and road grime and destroy the mesh pattern and stretch foam elements out of shape just squeeze it like a sponge and let air dry, use a fan if you're in a hurry. When completely dry spray a very fine mist of air filter oil evenly around the whole element.
6. Remove the carburetors, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove, clean, and inspect fuel and vacuum lines and replace as necessary.
8. Replace spark plugs with new ones and check for spark.
Good luck and have a wonderful day.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Mar 14, 2017
Tips for a great answer:
Aug 27, 2016 | Kymco Motorcycles
Aug 27, 2016 | Kymco Motorcycles
Feb 22, 2016 | Kymco 2010 MXU 375 IRS 4x4
Nov 20, 2013 | 2006 Yamaha Road Star Midnight Silverado
Jul 30, 2013 | Pit Bike 125cc 4 Stroke Dirt Bike
May 18, 2011 | Ducane F7011013
Aug 07, 2009 | 1981 Yamaha XJ 650
Apr 03, 2009 | 1991 Honda CB 250 Nighthawk
32 people viewed this question
Usually answered in minutes!