Question about Honda Motorcycles

1 Answer

Can the handle height on a honda hss928 be adjusted higher?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.

  • Honda Master
  • 60,964 Answers

Hi, Jerry you need to repost your question under the Snowblower category, not Motorcycles. Thanks, Gregg

Posted on Jan 17, 2020


4 Suggested Answers


Lauren Junge

  • 1673 Answers

SOURCE: handle height adjustment

It i called a detent lever, part # 2030052. Usually a repair shop can order this for you. Or you might try and see if you buy it online from them.

Posted on May 20, 2008



  • 112 Answers

SOURCE: seat height seems high according to specs ; vtx1100c2 2004

you could try a little bit smaller rear tire. cheaper than the shocks maybe

Posted on Jun 11, 2009


  • 127 Answers

SOURCE: Button on handle adjustment is missing

You can order the part for about $7 from perego call them at 1800-671-1701.

Posted on Oct 24, 2009

Marie Lowe

  • 223 Answers

SOURCE: The handle height adjustment button has stopped

You can replace the handle by buying a new or used 1 off ebay

Posted on Aug 21, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Adjust handle bar height ?

looking at some pictures of this model, most appear to be using an "Aheadset" style handlebar stem, there is not any way to raise this type of stem. Your alternative is to go online or to a local bike shop and purchase a new stem that will fit your fork and handlebar that has a higher pitch angle to it, or a compatible adjustable stem that pivots. Expect to pay $25-$50 or more for a new handlebar stem, not including labor to install.

Apr 06, 2016 | Marin Belvedere Commuter Road Bike

1 Answer

I have a Honda Elite 1998 CH80. Throttle won't increase when handle is rotated. I replaced jets and checked vac housing, adjusted needle height. Engine turns fine. Runs great at one speed.

With the engine off, Check the linkage cable from the handle to the carb, making sure , at full throttle at the handle the carb is at full throttle.

May 15, 2014 | Kitchen Ranges

1 Answer

How to adjust height on rear springs

adjusting the spring tension makes the ride harder and mite hold you up slightly ! is the adjuster on the top of the shock and rotates by hand coz thats the oil reaction responce , or is it below the spring which you need a tool to adjust ? if suspension is nearly full compressed after all these then fit longer shocks ! Dial a ride air shocks are good as you can select the height , not cheep though ! P...

Dec 21, 2013 | 1987 Honda VT 1100 C Shadow

1 Answer

Are there adjustments to the handle bars to raise them up

There are some small adjustments that can be made.
remove the centre consul where the key goes in.
This just lifts off from the rear.
Under that you will find a black cover, pull that off.
The handle bolts and clamps are under that.
undo the 2 rear bolts and you can then adjust handlebar angle and height.


Please dont forget to vote if you liked my answer


Feb 09, 2011 | 1999 Honda GL 1500 SE Gold Wing

1 Answer

I would like to adjust the rear suspention to a higher setting (Ibeleive it ahs eight) can anyone give me direction on how to access the adjusting part and how to make the adjustment

In the factory tool set in your bike should be a spanner wrench. It has a handle and looks like a C on the other end. Look on the top or bottom of the shock and you will see holes going all the way around it. The tip of the wrench fits into a hole and turns that part of the shock. Sometimes the shock has a little sticker on it with numbers 1 thru 5. If not, just turn it one click at a time to see all of the ride settings. Remember giving it more height will also make it a bouncier ride. Hope this helps...

Dec 01, 2009 | 1994 Honda VT 600 C Shadow

1 Answer

Need to adjust height of handlebar on a jeep sahara bicycle

Most bikes use an allen key to adjust the height of the handle bars. Typically 6mm. But be careful most bikes do not have much adjustment that can be done to the height of the handle bars. The handle bar stem will have a line on it of the "minimum insertion". That line must be below the top of the head set nut for safety reasons. Look for the line as you adjust the height.

Oct 03, 2009 | Jeep Cycling

1 Answer

Seat height seems high according to specs ; vtx1100c2 2004

you could try a little bit smaller rear tire. cheaper than the shocks maybe

Jun 07, 2009 | 2004 Honda VT 1100 C2 Shadow Sabre

1 Answer

92 honda accord camber adjustment

There is no no camber or caster adjustment on that model. If the car has been in an accident, chances are something is bent. My experience has been that the shock body and/or the steering knuckle is bent. Parts replacement is the only true fix. If the vehicle has had the ride height altered, ie. lowering springs, then there are adjustable upper control arms and ball joints available. These do generally only address the camber angle, not caster, which can also greatly affect handling. hope this helps.

Oct 20, 2008 | 1992 Honda Accord

1 Answer


hi have a 550 horsepower lawnmower and the height adjuster handle has broke where do i get my hands on a new one anybody out that can help please let me know thanks

Oct 14, 2008 | Husqvarna 160 CC Honda OHC Engine 21 in

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6151 Answers


Level 3 Expert

85223 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides