My clip has broken on my saddle bag, after searching the net I'm finding it hard to locate the replacement part iam looking for. It's the plastic part that attaches to the bag I need and not this following part that I find all the time on various sites. (Topeak TPK FIXER F11) Please help.... Chistian

If the plastic blue clip on your Oreck Magnesium vacuum cleaner has broken, you will need to replace it to keep the bag securely attached to the vacuum. Here are the steps to replace the clip:

1. Locate the broken clip. It is usually located on the underside of the vacuum, near the bag opening.
2. Remove the broken clip by gently prying it off with a flat-head screwdriver or a similar tool. Be careful not to damage the surrounding area.
3. Obtain a replacement clip. You may be able to purchase a replacement clip from an Oreck dealer or online retailer.
4. Attach the replacement clip to the vacuum. The clip should snap into place and hold the bag securely.
5. Test the clip to make sure it is properly attached and holding the bag securely.

I have the saddlebags....they are in good condition.
E-mail is [email protected]

I do think its in or under rt saddle bag..

You can purchase net bags that are designed to avoid exactly that problem - you put your items inside the bag and put the bag in the dryer.

Search ebay for 'laundry net bag'

Hope this helps.

try denniskirk.com

A bolt is underneth the driver seat at rear. Hard to see. Maybe pull off driver seat first the rear seat - be sure you are using a soft saddlebag
support. Don't get bags caught in wheel

Yes you will need brackets. You can find them at your Honda dealership. They mount to your fender where the two fender bracket bolts are located. You take the two bolts out, line the saddlebag brackets up with the holes, then replace the bolts. It should take about 5 mins.

Try looking under your seat. A lot bikes/atvs carry them under the seat. It feels hard to lift them up but there is usually a lever to release it just at the tip of the seat near the gas tank. Being an older bike more than likely it has been removed especially if it was purchased used. Cabela's has kits for about 50.00. You can log onto their website at www.cabelas.com. Search the site along the left side of the page it is very easy.

nstructions Difficulty: Moderate Things You’ll Need:

• Saddle bag set
• Power drill
• Screwdriver
• Ratchet set
• Measuring tape
• Scissors

Step1 Determine what type of saddlebags you will be installing on your motorcycle. Saddlebags come in hard and soft styles, with each installed in basically the same manner. Hard bags tend to offer more security for your items but are a bit on the bulky side, while soft bags offering a little more flexibility. Step2 Check to make sure that your fender bolt area is clean and prepped for installation of your saddlebags. Both hard and soft saddlebags on Harley Davidsons are installed over the fender bolt area on the rear of the motorcycle, so clearing this area of debris and grime will keep it free of scratches and blemishes. Step3 Install any spacers or lifting brackets before you try and place your bags on your Harley Davidson. These spacers will keep you bags from resting against your exhaust pipes and will avoid damage to your motorcycle and to the bags themselves. Make sure they are installed tightly and spaced properly before mounting your bags. Step4 Open the saddle bag packaging and lay out the included hardware. The hardware will be necessary to properly mount your saddlebags to your fenders, so be sure that you do not misplace it. If your saddle bag comes with a fender mounting bracket, install it along the fender before proceeding. This bracket will be used to hold and stabilize your saddlebags, so it is essential that it is properly tightened and installed. Step5 Hold your saddle bag up to the fender and align the bolt holes in the saddle bag with the bolt area on the fender. Your saddle bag will have mounting holes in the side of the bag that will align with the mounting bracket. Place one of the bolts in the hole and tighten to hold it on. Put the remaining bolt in place and tighten them both securely once they are aligned correctly. Step6 Repeat this process with the remaining saddle bag. The bags should align evenly and be attached straight to avoid any imbalances or shifting while the motorcycle is in motion. Try and wiggle or move the bags to be sure your bolts are tight enough to prevent movement. Step7 Take your Harley Davidson for a short ride. Stop and check the fitting on your saddlebags and look at your bolts. Make sure nothing has moved during your ride and that all of your fittings remain tight. With just a bit of effort, your new saddlebags will make your Harley Davidson the envy of the neighborhood.