Removing bearing from rear wheel 03 ultra classic

replacing bearing involves removing axle your not replacing a hub but tearing apart axle 99 04 F250 Sterling Rear axle bearing replacement Pt 2 2006 Ford F250 rear hub axle seal replacement F250 Rear Brakes Axle Hub Removal Install 03 07 Powerstroke

On an 03 bagger it will be under the seat. You'll have to remove it. Under the seat is the battery you should see a little silver clip towards the back ledge of the battery tray. That's the turn signal module. Remove the clip and pull the unit up amd out.

To remove a 2008 Softail rear wheel FIRST block motorcycle underneath the frame so that theweight of the motorcycle is off of the rear wheel, remove saddlebags if equipped, remove the belt guard and the debris deflector from the rear fork, inspect the wheel bearing end play and service the bearings if and as necessary, label the wheel spacers for left or right locationand orientation i.e. fork side or wheel side, remove the rear brake caliper from the caliper mount and support it using an elastic cord or such,For the FXCW/C modelsthe nut retainer will remain in the axle nut and does not need to be removed and if it is removed it must be replaced. For all but FXCW/C remove e-clip, remove the rear axle nut, and for FXCW/C remove the rear axle nut, loosen both axle adjuster screws an equal number of turns to remove tension from drive belt, with a suitable drift or other tool tap the axle towards the right side and remove it, remove the spacers and the caliper mounting bracket, move the wheel forward and slip the belt off of the sprocket, raise the motorcycle to allow enough clearance for removal of the rear wheel and pull the wheel with the belt sprocket from the rear fork.

To install a 2008 Softail rear wheel FIRST apply a light coat of wheel bearing grease to the axle, to the bearing bores and to the bore of the inner sleeve, roll the wheel into place in the rear fork and slide the drive belt over the drive sprocket, position the left bearing spacer between the wheel and the fork, from the right side carefully insert the axle (with its washer for FXCW/C models) through the right rear fork, the short spacer, the rear caliper mounting bracket, the long spacer and into the bearing bore, continue sliding the axle through the wheel hub sleeve, the left side spacer and the left rear of the fork, install the washer, the axle nut, and the retainer, verify correct axle alignment and the check belt deflection, check the wheel bearing end play after tightening the axle nut to the specified torque because excessive end play can adversely affect stability and handling and insufficient end play can cause bearing seizure, tighten the axle nut to 95-105 ft-lbs (128.8-142.5 Nm), install the belt guard and the debris deflector, install the brake caliper and pads, install the saddlebags, if equipped, pump the brake pedal to move the pistons out until they contact both brake pads, verify the piston location against pads, verify the position of the brake pads against the brake disc, rotate the wheel to check for any interference(s) or misalignment(s) and test the brakes for proper operation.

Thats is strange ..springs..!! I do not know ..sorry ,, If you wish you can join & post that ? on our forum harleytalking.com . good tecks there ...good luck.. ultrat..

remove two tiny torx head screws and pull them out of the caliper
remove old pads
clean and push piston(s) into caliper

easier with wheel off, or axle pulled out so caliper can "float"
a toothbrush work well with some brakecleans

Not sure what you are asking? The wheel alignment should align when you adjust your belt deflection by the axle cam.Unless you have changed the swing arm or any bearings or bushing in the swing arm.

This is a rear wheel drive vehicle? Are you sure it's not a brake squeal?
The bearing sits in the end of the axle tube and is lubed with the differential fluid. You need to dissasemble the differential to remove the axle, to remove the bearing. You need a puller for that type of bearing.