Question about Suzuki Motorcycles

1 Answer

Will not turn over 2007 Suzuki Skywave 250

I have a skywave 250cc type S mod 2007 with the keyless ignition system. When I click the start key it is not taking the command from the remote I think it should be reprogrammed together can somebody help me how to do it? @

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Suzuki Master
  • 59,350 Answers

Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://burgmanusa.com/forums/14-burgman-400-1999-2006-model-years/48429-won-t-start-engine-will-not-turn.html
What To Do If Your Motorcycle Doesn Start
https://www.croooober.com/en/item/3878013/Other-Accessories/SUZUKI-Skywave-250-Service-Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Posted on May 14, 2019

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
nitro650

Edward Zammit

  • 93 Answers

SOURCE: hello. i have a skywave 400 2008. its key is like

check the electrics if they are fried, you need to change them

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changed battery in keyless remote and now doesn't start car or open doors


  • HOW TO - Change the battery and quick fix your car remote ...

    ? 9:32
    https://www.youtube.com/watch?v=KzCXGXCe0oc
    Sep 1, 2011 - Uploaded by tyreeztt
    Also if your remote isn't working with a new battery please check out this ... TO - Change the battery and quick fix your car remote / keyless entry ...

    Remote Key does not lock / unlock doors after battery change ...

    www.6speedonline.com/.../208274-remote-key-does-not-lock-unlock-do...
    Apr 17, 2010 - After I changed the battery, it would no longer lock / unlock the doors. ... I can start the call and all .. its just the door and trunk lock / unlock function that does not seem to work . ... now your fob is learned... the keyless entry goes into a "sleep" mode to preserve the batt.. if u do not use the ... Still don't work .

    how do i reprogram my lock remote to my car? i changed my ...

    www.cargurus.com > Questions > Hyundai > Tiburon

    CarGurusAug 17, 2009 - i change my battery an now my lock an un lock buttons dont work on my remote how o i reprogram it? ... I have a Hyundai 2003 Tiburon, and the followingworked for me, get ... However for a replacement keyless remote fob, you will have to go to ... And no, they don't do it for free (ranges from $30-$50 in my ...

    Top 5 Tips in Fixing a Keyless Remote ' eBay

    www.ebay.com > ... > Safety & Security > Keyless Entry Remote / Fob
    Key fobs that don't permit entry can be a major hassle for drivers, but fortunately, there... Drivers with a bit of basic electronics experience are often able to replace their ...After confirming that a remote is faulty, try replacing its battery. ... like "Jeep Wranglerkeyless remote," to find listings that will work with specific vehicles.

Jan 26, 2016 | 2005 Ford Freestyle

1 Answer

HAVE A PRESTIGE APS686T REMOTE START ON A2003 FORD FOCUS.HAD 2 NEW KEYS PROGRAMMED. THE REMOTE START FLASHES MY THEFT LIGHT AND WILL NOT START. HOW DO I PROGRAMM THE PRESTIGE TO MY KEYS.


When you had the new keys programmed, the bypass was erased. More than likely, it was a key. Try this: put the first of the two new keys into the ignition, turn the ignition on. The theft light will light up, then go off. Immediately remove the key and put the second key into the ignition. Turn the ignition on, the theft light will come. When the theft goes out remote start the vehicle with the remote, quickly remove the key from the ignition. If the vehicle starts let it run for a few seconds and then shut the remote starter down with the brake. Wait a few seconds before testing the system.
If the above programming does not work the first time, try it again. It may take a few attempts because the process is time sensitive. You CANNOT allow too much time to pass between switching the keys.

Jun 01, 2011 | Prestige APS686T Remote Start and Keyless...

1 Answer

Yes i have a 2007 gmc yukon denali. when i bought it they didnt give me the keyless entry pad with remote start, then when they did give me one it wasnt the one for my vehicle, they told me all i had to do...


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Feb 11, 2011 | 2007 GMC Yukon Denali

1 Answer

2002 chevy malibu wont start i think it is the anti theft system.


If this is so then it is defeating OFF the power to the ignition system. Check the power to the ignition system or check to reset the theft alarm if this was activated. Using the keyless remote and the ignition key into the holder reset the qalarm if this has tripped with a false entry.
If not check the fuel and ignition for the failure of command from the ECM.

Dec 03, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

My 2007 Ford Edge W/ Mars 22 remote start will start for 2 seconds when you hit the start button then shut off then start again then 2 seconds later shut off and will repeat this 2 more times, then will...


put your key in the ignition leave it in the off position, push your remote start button, if it starts then it has something to do with the transponder bypass "key in the box" or the loop around the ignition switch under the plastic cover

Feb 23, 2010 | Omega MARS-22 Remote Vehicle Starter with...

1 Answer

2007 Suzuki Skywave 250 type M not shifting


Hi, Sylverwing for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://burgmanusa.com/forums/25-burgman-399cc-below/42587-skywave-250-type-m-manual-shifter-2.html
http://burgmanusa.com/forums/15-burgman-650/37010-shifting-problem-error-c51-automatic-mode.html
Suzuki Burgman UH125 Service Manual
OEM parts for Suzuki
Suzuki Skywave 250 Type 2005

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jul 27, 2017 | 2010 Suzuki Burgman 125

2 Answers

2006 Mazda 5 keyless remote fob


I am a technition for mazda, and if the lights are coming on to the keyfobs, the batteries are fine. What procedure did you follow?
1. Take key out of ignition
2. Shut all doors
3. Open drivers door
4. Insert key to ignition
5. Cycle between On & Lock 3 times, leaving key in Lock
6. Close and open the drivers door 3 times, leaving the door open
7. The Locks should cycle.
8. Press the Panic button on the remote twice.

Jan 31, 2009 | Alarm & Keyless Entry System for Mazda...

1 Answer

Remote start is intermittent working


the problem is your car is equiped with a passlock system you need a by pass mod. part number 555-L this is a dei part number this is the only company i use. it is a simple three wire hook up. if you got this far you will not have any trouble. one other thing to check is your ignition wirers make sure they have power when they are suposed to.if your still having problems or need more info on getting part let me know. i have alot of exp. with auto starts and keyless entry.

Jan 09, 2009 | AutoCommand Remote Start and Security with...

4 Answers

Keyless remote


THIS IS THE PROCEDURE, FOLLOW IT EXACTLY OR IT WILL NOT WORK.



Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Sep 25, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers

ROB

Level 3 Expert

858 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...