Question about 2005 Harley Davidson FLSTN- FLSTNI Softail Deluxe

1 Answer

Brake lights wont work with hand or foot pedal. Tail lights work fine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 867 Answers

Most likely the filament blew, change the bulb, there are two filaments in the bulb, one for tail light and one for brake.

Posted on Jun 17, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dim tail light.


Brake light switch under dash and actuated by the brake pedal lever is out of adjustment or faulty. Adjust or replace it and you'll have your brake lights back. The dim tail lights may just be that you have possible replaced them with the wrong bulbs or the ground to light housing is faulty.

Jul 11, 2017 | Cars & Trucks

1 Answer

I've got a 1975 GMC Sierra C15. The tail lights and turn signals work just fine but the brake wont come on. Can anyone help me out? The tail lights turn signals and brakelights all work on one bulb.


Your brake pedal controls a switch that turns the brake lights on. If the switch or the wires from the switch are broken, no brake lights.

Jun 03, 2015 | GMC Cars & Trucks

1 Answer

2005 softail classic brake light problems


test the line for a break or short.

Mar 12, 2014 | Motorcycles

1 Answer

Brake lights wont work when pressure is applied


brake switch needs adjustment if it works with slight pressure on the pedal readjust it where it needs to be..

Feb 09, 2013 | 1999 GMC Yukon

2 Answers

Tail light and foot pedal brake light does not work but hand lever brake light works.


Probably a bulb/ rear brake switch combination. If your front brake switch is working, then half of the bulb is working. No taillight issue, probably a bulb. No rear brake light, probably the rear brake switch. Located on the lower right rear of the frame, behind the exhaust. Check for power on the orange/white wire at switch. If you have that then check for power on the other terminal of the switch while pushing on the pedal. The rear brake switch is hydraulically operated so you must have adequate pressure to activate it.

May 04, 2012 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

My 2003 750 shadow spirit tail light/brake light is always on


Ensure the bulb is correctly fitted!!

You must have a foot hand brake switch mal-adjusted / faulty. back them both off (If possible) and it should extinguish.

Does it still work with headlamps off?? If so then one of the switches are faulty / need adjusting.

May 13, 2010 | 1984 Honda VT 500 C Shadow

1 Answer

Brake lights wont work right tail light wont work 2003 gmc envoy


check globes and check brake light switch under dash on brake pedal.

Oct 27, 2009 | 2004 GMC Envoy

2 Answers

My tail lights dont work, its not a fuse, my blinkers and reverse lights work, its just my running lights and my brake lights that dont, any suggestions?


check the wire harness that runs from inside the trunk on the drivers side follow it down to the tail light and make shure the wires are not damaged or unplugged remove cover on the drivers side inspect the bulbs the holders and the wires and dont forgt to retighten all grounds that you find on your travels this should get the rear tail lights working also check the brake pedal switch up on the metal part of the brake pedal arm follow it up tp the brake pedal switch and acuate the switch by hand and check the wire voltage coming in and going out when pressing the brake pedal ok give this a shot

Jul 21, 2008 | Ford Mustang Cars & Trucks

2 Answers

2000 crown victoria -brake lites failed


You have a bad switch at the brake pedal. Or a loose wire. Try light pulling on the wires on the switch at the brake pedal under the dash. They should be tight and secure. If tight and secure the switch could be bad.

Jul 03, 2008 | 2000 Ford Crown Victoria

Not finding what you are looking for?
2005 Harley Davidson FLSTN- FLSTNI Softail Deluxe Logo

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5968 Answers

Mike

Level 3 Expert

4363 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...