What does -c29 in my gsxr 600 2007 - 2007 Suzuki GSX-R 600

Question edited to add full 'year maker model'.

Code 21

https://www.google.com/search?q=2008+Suzuki+GSXR-750.+Error+Code+C21

All about Code 29

https://www.google.com/search?q=2008+Suzuki+GSXR-750.+Error+Code+C29

..

You just go to the link I attached I'm sure you will get the solution of your problem
gsxr 600 Here's the link

ftp.qrz.ru/pub/.../tv/hitachi/HITACHI-29TF751/hitachi-29-tf751.pdf

GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

heres a list of fault codes hope it helps

John

factory setting code c29-f300b

C29 = Secondary Throttle Position sensor. The sensor should produce the following voltage, 4.8 volts.
Check all the electrical connections and plugs to and from your carbys. mabey your battery is getting a bit low also?

When the red light comes on, eg (F1) use these fault codes to find your problem. To extract the codes from the computer system, there is a two pinned connector hanging out of the wiring harness, on the left hand rear of the bike, (say above the pillion foot peg under rear trim. Be sure not to confuse the other connector used by the Suzuki Workshop Mechanics, as this has four or five wires to the connector) After locating the one with only two wires at the back, use a split pin or paper clip to bridge the two wires togeather and turn the ignition to the ON position. You should now be able to read the code on the console. The fault codes are as follows,,
**** GSXR Fuel Injection (FI) Code List:*****
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL

You can get original replacement remotes here (warning: they are a bit pricey)

http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=C29-F800S+&uuid=12609245072340

vertical amlitute

According to Hitachi themselves, there is no such set with model number C29-F100. The closest one they have on file is the C29-F800. Perhaps your set is an over-seas set, originally sold in Japan? The original remote has a MENU button surrounded by 4 "arrow" buttons - arrow up, down, left and right. For the C29-F800, using the original remote, press the MENU button 4 times or the SETUP button once. There should be 4 choices on that page and the first one, the one on top, is LANGUAGE. Highlight the first one using the "arrow down" (also labeled P-) button and select the language ENGLISH using the left or right arrow buttons. Exit the menu by pressing MENU 3 more times or SETUP once. I believe I can download the owner's manual for the C29-F800 and send it to you if you need it.