1995 Neon Instrument Cluster Wiring Diagram

There is no such thing. That's simply not how wiring diagrams are arranged. They're arranged by system, not location. Read this post on how to find what you need.

http://ricksfreeautorepairadvice.com/get-car-wiring-diagram/ How to get car wiring diagram Ricks Free Auto Repair Advice

Scroll to the bottom of this post for sources of wiring diagrams
How to get car wiring diagram Ricks Free Auto Repair Advice

• The tachometer is inoperative

• Instrument cluster.

• INSTALL a new instrument cluster; REFER to Instrument Cluster . CLEAR the DTCs. REPEAT the self-test.

ingntion what ? ignition switch , ignition as in ignition system - coils etc... The instrument cluster is probably related to ignition problem. Do you know how to read a wiring diagram ? http://www.bbbind.com/free_tsb.html free wiring diagrams . Buy yourself a DVOM - digital volt ohm meter , check out some videos on youtube on basic automotive electrical testing , how to use a wiring diagram

Hi, it's possible the bulb is burned out or not making good contact with the circuit board. It should come on during the bulb check when you first turn the key on. Pull out the cluster and check the bulb. If it's good, see if you can clean the contact surfaces to get it working again. Or, move to another state where they don't worry about stupid things like a light bulb.

REMOVAL & INSTALLATION

See Figures 1, 2, 3, 4, 5 and 6

Fig. Fig. 1: To remove the instrument cluster, first remove the trim panel by removing the lower fascia panel

Fig. Fig. 2: With the lower fascia moved aside, remove the lower trim panel attaching screws ...

Fig. Fig. 3: ... as well as the upper attaching screws

Fig. Fig. 4: Then pull the entire instrument trim panel from the dash board

Fig. Fig. 5: Exploded view of the instrument cluster

Fig. Fig. 6: Rear view of the instrument cluster wire routing and connections

1. Disconnect the battery ground cable.
2. Remove the two steering column shroud-to-panel retaining screws and remove the shroud.
3. Remove the lower instrument panel trim.
4. Remove the cluster trim cover from the instrument panel by removing the eight screws.
5. Remove the four instrument cluster to panel retaining screws.
6. Position the cluster slightly away from the panel for access to the back of the cluster to disconnect the speedometer.

If there is not sufficient access to disengage the speedometer cable from the speedometer, it may be necessary to remove the speedometer cable at the transmission and pull cable through cowl, to allow room to reach the speedometer quick disconnect.

1. Disconnect the wiring harness connector from the printed circuit, and any bulb-and-socket assemblies from the wiring harness to the cluster assembly and remove the cluster assembly from the instrument panel.

To install:

1. Apply approximately 1 / 8 in. diameter ball of D7AZ-19A331-A Silicone Dielectric compound or equivalent in the drive hole of the speedometer head.
2. Position the cluster near its opening in the instrument panel.
3. Connect the wiring harness connector to the printed circuit, and any bulb-and-socket assemblies from the wiring harness to the cluster assembly.
4. Position the cluster to the instrument panel and install the four cluster to panel retaining screws.
5. Install the panel trim covers and the steering column shroud.
6. Connect the battery ground cable.
7. Check operation of all gauges, lamps and signals.

if you take out the instrument cluster,you will find that it has a double sided pc board. the connector will have broken solder joints on the inside of the pc board,so it has to be removed from the cluster housing to see it.resolder the pins and it will be fine.I have seen 50 of those

I have the instrument cluster diagrams, need an email address to send to in pdf format

Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.

sure you can relax and look at them if they don't detach at the cluster then trace the ware about 5 inches in and it should be right there

try these:
www.allfordmustangs.com/forums/attachments/94.

http://www.veryuseful.com/mustang/tech/engine/images/Mustang-94-95-instrument-cluster.gif

or google: 1995 mustang cobra engine wiring diagram

PLEASE RATE MY ANSWER.