Top 20 Minolta Riva Zoom 70W Film Camera - Page 7 Questions & Answers

Hi, please ensure that you've changed between all 4+ camera modes within your camera. If this fails, then you can remove the Sd card and then afterwards remove the batteries. After 1 minute, you can re-insert the batteries back into the camera without adding the sd card and check for the error again. If this fails, then you can re-insert the sd card and check again. Otherwise, you might need to take camera to Geeksquad/Bestbuy for repair. Thank you.

It is here https://van-eck.net/en/product/hanimex_1000_dls_instdual_8_user_manual-_languages-_english/ ..

The only thing you can try is a full strip down and check the connectors to the screen display. They may be a ribbon connector.

No 'make model (what it is). 'Drv'?? Replace or repair whatever went 'pop'. A resistor or capacitor or even IC has failed.

I would try the manufacturers web site and follow the link to service/repair agents.

Hi, Yes. if your camera needs a specific brand of battery, then you can search for that brand on amazon's website and then just order the brand and type of battery that your device needs and it will be sent to you in a few days. Otherwise, you can call the manufacturer and ask them if other brand's of battery can be used with your camcorder to give it power. Thank you.

Hi, Please call Kenwood to ask about the language update information or manual for your device. They should be able to email the manual to you. There phone number is 1-800-536-9663. Thank you.

Hi, please use Amazon or ebay to acquire a compatible remote so that you can move forward with updating the device language. You might also call local stores that offer device rentals to request a temporary rental or use of the camera remote. Thank you.

The silver knob above the leg knob on a Bell and Howell 455A movie projector is the speed control knob. This knob is used to adjust the speed at which the projector runs. The projector has three speeds: 16, 18, and 24 frames per second (fps). This knob can be used to match the speed of the projector to that of the film being projected. The user can switch between the speeds depending on the format of the film they are using. When the projector is set to the right speed, the motion in the film will appear smooth and fluid, with no stuttering or jerking

camera markers name not told CANON, NIKON or? no model camera told, of VAST. Lens jams are 3 fold caused battery is bad, too weak to run camera lens motors, !!! or sand (dirt) got into the lens and jammed or camera dropped and broke the lens. get it fixed in a camera shop> or upgrade it.

Hi, please restart your car once (from the ignition). And while placing your foot on the break, move through all gears (ie drive, park, reverse) before stopping on parking. If issue still remains, please check your steering wheel levers for any options with the letter "S" and test the option in order to overcome the issue. Thank you.

"this camera", the only only you can see? Impossible to answer because you give no clue to that you have. Click Comment below my post. Give me full make and model and what type of camera.

Try to find the diagram you are looking for by contacting the manufacturer or searching online for a manual or guide for the Ryobi HBT250 table saw. Some resources that may be helpful include the Ryobi customer service, online forums, or repair websites. If you have the saw's model number and serial number, you may be able to find specific information on the motor assembly.

Hi, Please double check that the battery brand has been approved by the manufacturer. Also, please check with manufacturer that lockpad does not have issues based on external temperature as the locakpad functionality could change in times of hot summer or freezing winter. If all else fails, please schedule a repair with either Home Depot or Lowes. Thank you.

most likely need battery here is instructions copy and paste https://cdn.amplifi.pattern.com/730b494e-455d-4fcc-9365-e5c22ebe7935 ..

Hi, please make sure that your camera has an SD card inserted into. Otherwise, you won't have any memory with which to save the pictures that you take. You can also look into changing the modes of your camera. Thank you.

Make and model of camera, may help you get an answer.