Kenneth Cole 1213 Wrist Watch - Answered Questions & Fixed issues

no chance to remove the box it is held in place by a nut on the spindle shaft from the face of the clock under the hands

email [email protected] to get strap for your watch.

you need watchmaker tool to pry up.

this strap is out of production

Thanks for contacting FixYa.

Tough one to find. You can try:

http://www.watchbands.com/custom.aspx,,id,,34,,Request-Kenneth-Cole-WatchBand-Quote

Best regards. Jewel

if you cannot open it, just bring it to watch service center because they all have the tools for opening and closing your watch. and to avoid much problem. i hope i had been helped you,

Kenneth Cole watches are made by the Geneva Watch company.

If you go to their web site http://www.genevawatchgroup.com/, you will see their contact number under "Customer Service". They should be able to help you.

The user instructions that the maker publishes are generic only and not model specific, so try go to http://www.genevawatchgroup.com/pdf/kc_reaction/KennethColeReaction_US.pdf and scroll down to the alarm setting section.

With any luck, your watch will be covered by these instructions.

Good luck!

You can get instructions by following the following link to the Geneva watch group (who make the watch) http://www.genevawatchgroup.com/

Click on customer service and the scroll down the page until you find your watch and download the instructions.

THIS MEANS YOU BOUGHT A KNOCK OFF. Try and locate the place you bought them from and make a formal complaint and ask for a refund.

You can get the instruction manual here:
http://www.genevawatchgroup.com/pdf/unlisted/UNLISTED-GENERAL-ANALOG-DIGITAL-INST.pdf

dfghjkl

Download the manual here
http://www.genevawatchgroup.com/pdf/unlisted/UNLISTED-GENERAL-ANALOG-DIGITAL-INST.pdf

The arrows show you the direction to push out the pins.

Look for an arrow on the inside of your watch band. The direction the arrow is pointing is the direction the pin should slide out of the band. If your pin is screwed in, you may not see an arrow on the inside of your band.

2 Look on the edge of the watch band for a small round object, the pin. If the pin head is flat, then it needs to be pushed out. If the pin head has a screw driver groove, then it needs to be screwed out. Depending on the type of watch pin you have, take a sharp pointed tool or a tiny screw driver from a hobby kit or watch tool kit and place it on the head of the pin. You should be looking at the end of the pin on the opposite side from where the arrow is pointing.

3 Push on the sharp tool to push the pin out of the watch band. You will need to use force to push the pin out. If your pin is screwed in, gently unscrew the pin until it becomes loose. Remove the pin with your fingertips. Make sure to put the pin in a safe place, because you will need it again when resizing the watch band.

Buy it on eBay.

how do i shorten the watch band without breaking it???

If you don't have the proper tools I recommend that you not do this yourself. You could scratch the case or damage the movement if you don't know what you're doing. If it's a water resistant watch the gasket also needs to be replaced once it is opened. DO NOT reuse a gasket! For about $8 any watch or jewelry store can change the battery and renew the gasket for you.

as any watch strap through a jewelers or through KColes website they will ship any place normally at a price..it will have to be ordered if you are any place on the planet..not just Aus..

Use this link to contact KENNETH COLE: http://www.kennethcole.com/helpdesk/index.jsp?display=store&subdisplay=contact Rate me, plz.

Take the watch to a reputable watch repair shop, many Sears stores have a watch repair center in them. Have them do the band adjustment! Its nearly impossible to push those pins out with a paperclip or needle.