Bowflex Treadclimber - Page 3 - Answered Questions & Fixed issues
Err L5
this meand 2 alternatives:1) problem with the display board adjust the reed switchsee the diagram2) mean the elevation motor; lube the gear and shaft ,and adjustment the potentiomenter, and check the voltage input motor .God bless you
6/20/2012 3:32:30 PM •
Bowflex...
•
Answered
on Jun 20, 2012
•
677 views
What does the h24 h13 h3 code mean
this is codes are y bad design from Bowflex, you must contact them and explain , they exchange the electronics boards for news ones with better design. I am sorry. God bless you
5/26/2012 1:36:57 AM •
Bowflex...
•
Answered
on May 26, 2012
•
278 views
Error code h3,h13 and h24
Dear Sir:This a problem from bad design from bowflex, you must contact them with service support for to replace the hardware.You must do it. sincerely. God bless you
1/18/2013 1:26:12 AM •
Bowflex...
•
Answered
on Jan 18, 2013
•
378 views
Bowflex treadclimber gives error code h13 h24
this a problem with a bad design from a factory. You must call to service support a explain this error. Is a problem,with a PROM AND EPROM.However you can try to RUN the software calibration for diagnose, and troubleshootingl.God bless you
5/9/2012 12:49:43 PM •
Bowflex...
•
Answered
on May 09, 2012
•
681 views
Stuck on high speed
Run the software calibration for diagnose, troubleshooting, and fix it.sincerely. God bless you
5/6/2012 11:11:33 AM •
Bowflex...
•
Answered
on May 06, 2012
•
78 views
Treadclimber stiff treadles
When you are in need of step two upwards, you'll find it together with the
Bowflex TreadClimber Thread count 4000, with exactly the same dimensions not to mention measures 1800. The actual velocities start around .Five in order to Several.3 miles per hour. You possibly can course performance, effort, gap, calories burned, calories from fat each and absolute procedures, and you may be able to get pleasure from a strong ergonomic desk games console. You can find parts with respect to drinking water together with magazines and catalogs and it also consists of a a few 12 months service contract.
4/30/2012 3:50:14 PM •
Bowflex...
•
Answered
on Apr 30, 2012
•
156 views
Calibration
Dear Sir:1)See the attached diagram for Reed switch , clean, tigh the connector very well. Read carefully your instruction manual for software calibration for diagnose +trouble.If you do not have go to the next web and download for free: www. fitness. manualsonline. com sincerely. God bless you.
4/21/2012 3:36:14 PM •
Bowflex...
•
Answered
on Apr 21, 2012
•
92 views
I have a TC5 and the console is not working correctly
Dear Sir:Please 1) adjust the reed switch attached is diagram 1a)Tight the flexible cable from keypad + tight the connector from display board vs lower board.2) Run the software calibration for easy diagnose and troubleshooting.If you can Not run your s. calibration see my personal TIPS, for diagnose and troubleshooting. sincerely. God bless you.ernesto cuadramanagua, nicaragua. c.a.
2/29/2012 7:41:42 PM •
Bowflex...
•
Answered
on Feb 29, 2012
•
499 views
Who can repair my bowflex treadmill 5 series in toronto
There are four typical causes for this problem :
1) The walking belt and/or deck are worn. (85% of the
time)2) The walking belt and/or motor belt are too
tight- if you have adjusted either recently. (8% of the time)3) The motor has lost torque and needs brushes or has
demagnetized. (5% of the time)4) The controller board is
dropping output. (2% of the time) . You can do it foryourlsef. However i will give some websites FOR TO CONTACT THEM:www.unitedassemblers.com + www.treadmildoctor.comSincerely. Merry Christmas.ERNESTO CUADRAMANAGUA, NICARAGUA.
12/19/2011 7:18:49 PM •
Bowflex...
•
Answered
on Dec 19, 2011
•
332 views
In the treadclimber mode. One
pull adjustment knob out.Set the swing arm in the position hightest and release the knob to lock the arm in place.Look at the clips at the end of the cable.If they hang down and are not tight againt the pulley,tight the pulley.locate the tension knob in the side- Pull the knob and turn the pulley bellow the know clockwise.Watch the clip above you retract.Stop turning the tension knob when the clip touches the pulley.Repeat with the other cables. sincerely
12/1/2011 11:32:54 PM •
Bowflex...
•
Answered
on Dec 01, 2011
•
208 views
Not finding what you are looking for?