20 Most Recent Samsung WF317AAG Front Load Washer / Dryer - Page 2 Questions & Answers

For front loaders, they usually have the level underneath the door, they use small amounts of water, but they spin so all the clothes do get
soaked with water.

to properly install this you nee to remove the retaining spring on the front of the boot.
then remove the lid.
next remove the four screws that hold the control panel in place.
then remove the four screws that hold the fron panel in place ther may also be two screws on the bottom of the front panel.
once you remove the front panel you need to set it aside but the door lock switch is still attached so be carefull.
one you remove the front panel you can get to the other retaing spring and remove the boot.it is easier for me to also remove the counter weights on the front of the tub.to put the boot back on.i hope this helps would like to here more on your progress

Is the machine draining if not clean filter

Videos in the link https://www.google.com/search?q=Samsung+WA80G5+washing+machine+pulsator+is+not+working ..

Question edited for clarity. Check the water inlet solenoid. It sounds like it has failed. It should open and let the water in from an instruction from the controller.. https://www.google.com/search?q=Samsung+WW80v9+no+water ..

Check the Door Latch and Alignment: Ensure that the door is completely shut and latched. Sometimes, clothing or debris can get caught between the door and the latch, preventing proper closure. Make sure there's nothing obstructing the door. Inspect the door seal for any damages. A damaged seal might not allow the door to close securely. Child Lock Feature: Samsung washers come with a child lock safety feature. If the child lock is engaged, it prevents accidental start of the wash cycle. Check if the child lock is activated. If so, disable it and try running the wash cycle again. Motor Control Unit (MCU) Inspection: Visually inspect the Motor Control Unit (MCU) board for any burned spots. The MCU is located on the left side behind the lower access panel. If you find burnt spots on the MCU, it might be the cause of the issue. You can order a replacement MCU if needed. Other Troubleshooting Steps: Reset the washing machine by unplugging it and then plugging it back in after a few minutes. If the problem persists, consult a technician to inspect the lock mechanism or control board.

Question edited for clarity. It won't be anything to do with the filter. It is either the motor controller, the capacitor or the control board. It need professional diagnosis. https://www.google.com/search?q=Samsung+SW674ASP+washing+machine+that+won%27t+spin ..

Is this the flexible pipe coming out of the back of the machine or the pipe work inside the machine? The flexible pipe (usually grey in colour) is a 'push on' fit. You'll need to get in behind the machine. With a bit of wiggling and twisting the pipe should pull off at the machine end. You should then be able to get the whole thing out from behind the machine to clean it. I used an long, old piece of wood dowel to loosen the dirt. I then carefully flushed it through using a garden hose with the nozzle set to jet, not to the wide spray pattern. I know this because I got very wet making that mistake.

Contact your honeowner's insurance company and see if that damage is covered. I don't think any reputable company would advise 'reclaiming' parts of a cleaning device that sat in raw sewage.

I have a problem with the Samsung WA80U3 washing machine. The safety stop button is activated and I cannot cancel it even though I tried to press the water level + function for more than 5 seconds and there is no solution. Please help.

Check the lid switch. Some models will not start washing if it detects that the lid is open.

Try a power reset. Disconnect from the mains socket. Wait 15 minutes. Press and hold Power Button for 1 minute. Plug back in. https://www.google.com/search?q=samsung+wa12v5+unresponsive ..

Question edited for clarity and toss in some CAPS. The all have alpha numerical model numbers. I think it is this one. What type of 'access panel' are you looking for? https://images.webfronts.com/cache/frdvahdqyvrv.pdf https://www.google.com/search?q=samsung+steam+aqua+jet+vrt ..

Here is a list of issues that are common https://www.samsung.com/uk/support/model/WD0804W8E1/XEU/ but you may need a replacement control panel now. If water/liquids ingressed the control board or a bad connection on the board has happened, that is another probable cause.

check under agitator possible bad gears or cogs

check the cold water valve is working