20 Most Recent
Whirlpool WTW6400SW Cabrio Washer - Page 9 Questions & Answers
Keep getting F50 code cannot reset washer
There have been a lot of reports where technicians have been ordering RPS's prior to the common fix for the problem which is the control board. This is a common problem and the control board fixes F50 faults in most cases.
11/8/2011 12:30:55 PM •
Whirlpool...
•
Answered
on Nov 08, 2011
I keep getting an F symbol on my washer. It's
Hello & Welcome to FixYa
F error in your whirlpool cabrio indicates bad
control and should be replaced to resolve the error code. However, you can
contact Whirlpool as well prior to replacing the control yourself as I have
seen whirlpool paying for the parts themselves just because this is known to be
a common issue. Please get back to me if you have any other questions.
Kevin
11/1/2011 1:47:27 PM •
Whirlpool...
•
Answered
on Nov 01, 2011
I don't know what the issue is. It just keeps
Hello & Welcome to FixYa
F1 error in your Whirlpool Cabrio indicates bad
control and should be replaced to resolve the error code. However, you can
contact Whirlpool as well prior to replacing the control yourself as I have
seen whirlpool paying for the parts themselves just because this is known to be
a common issue. Please get back to me if you have any other questions.
Kevin
11/1/2011 1:46:11 PM •
Whirlpool...
•
Answered
on Nov 01, 2011
THE F CODE COMES ON AND MY CABRIO WHIRLPOOL WASHER
Hello & Welcome to FixYa
F1 error in your whirlpool cabrio indicates bad
control and should be replaced to resolve the error code. However, you can
contact Whirlpool as well prior to replacing the control yourself as I have
seen whirlpool paying for the parts themselves just because this is known to be
a common issue. Please get back to me if you have any other questions.
Kevin
10/15/2011 5:52:44 PM •
Whirlpool...
•
Answered
on Oct 15, 2011
My washer, Whirlpool Cabrio, sounds like it is
Hi Jane from retired Englishman in SW France,
Normally I would advise cleaning/clearing the drain filter but for some reason the Cabrio does not have an easily acccessible filter fitted just before the drain motor like other washers of other (sensible!) manufacturers.
So- it is really a case of having you, or someone else, check the drain motor itself to see if IT is blocked and the drainage pipes/system. Sorry ;-0(
If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C
10/2/2011 7:29:35 PM •
Whirlpool...
•
Answered
on Oct 02, 2011
IN THE WASH CYCLE THE
Hi, the OL code means Overloaded..
OL flashes when the machine/motor control detects a load size that exceeds the washer's capacity.Open the door lid to clear display, remove excess laundry, then restart the cycle.
9/23/2011 5:11:13 AM •
Whirlpool...
•
Answered
on Sep 23, 2011
Dl code comes on on
A Door Lock Error occurs if the door cannot be locked. It will try to lock it six times before displaying the error code. It has happened because Door lock mechanism is broken or removed from door. It may also happen due to Door switch/lock unit failure. To resolve the issue follow these steps---
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU).
9/20/2011 4:20:30 PM •
Whirlpool...
•
Answered
on Sep 20, 2011
Washer won't fill with water
Hi from retired Englishman in SW France,
(pre-typed- I don't type that fast!)
If you have checked that the hot and cold water taps are turned on fully and the hoses are not kinked or squashed at the back, it is worth while checking both the hot and cold water inlet filters. Turn the taps off and remove both hoses at the washer end. Inside each inlet port there is normally a little filter which should just slide out. Clean if necessary and replace each one and the hoses. If after turning the taps back on there is no improvement, the problem is symptomatic of a malfunctioning hot or cold water control valve. Sorry but it needs a service call and a check that it isn't the control PCB ;-0(
If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck,
John C
8/13/2011 9:12:24 PM •
Whirlpool...
•
Answered
on Aug 13, 2011
Where can I purchase the
The part number is W10189966 it could be purchased from your local appliance parts store or online at;
searspartsdirect.com
apwagner.com
repairclinic.com
appliancepartscenter.com
8/12/2011 3:55:59 PM •
Whirlpool...
•
Answered
on Aug 12, 2011
I have a wtw6400sw and
Hello & Welcome to FixYa
F1 error in your whirlpool cabrio indicates bad
control and should be replaced to resolve the error code. However, you can
contact Whirlpool as well prior to replacing the control yourself as I have
seen whirlpool paying for the parts themselves just because this is known to be
a common issue and yes even if its a 4 yrs old they have to fix it. Please get back to me if you have any other questions.
Kevin
7/31/2011 11:53:03 PM •
Whirlpool...
•
Answered
on Jul 31, 2011
Not finding what you are looking for?