Yes, good diagnostics and summary. Don't guess with control boards for exactly the reason you stated. Call for service, you need the correct diagnosis and warranty on the part and the service call. There are indeed expensive and not for guessing.
To diagnose the issue with the Speed Queen SC30BC washer, it's important to determine which component is causing the fuse to blow. Here are a few steps you can take to help identify the problem:
Unplug the washer and visually inspect the wiring and components for any signs of damage, such as frayed wires or melted components.
Check for any loose connections, and tighten them if necessary.
Use a multimeter to measure the resistance across the wiring and components. If the resistance is very low, it may indicate a short circuit.
Check the drain pump for any blockages or damage.
Inspect the control board for any signs of damage or melted components.
Test the door switch to make sure it is functioning properly.
Test the water level control valve to make sure it is not stuck open and allowing excessive water into the washer.
If you are not comfortable with electrical repairs, it's best to call a professional for assistance. Attempting to repair electrical equipment without proper training can be dangerous and potentially damaging to the machine.
If your Speed Queen washing machine is stuck on a cycle, there could be a few different issues causing the problem. Here are a few things you can try to troubleshoot the issue:
Check the power supply and make sure that the washing machine is properly plugged in and receiving power.
Check the fuse or circuit breaker to make sure that the washing machine is not tripping any electrical circuits.
Make sure that the washing machine is not paused or paused on a cycle that is longer than usual. If the machine is paused, simply press the start button to resume the cycle.
Make sure that the washing machine door is properly closed and latched. If the door is not properly closed, the machine may not start or may get stuck on a cycle.
In the back of the cold water hose connection there is a small gauze filter. Check is is clear of limescales and debris. While the hose is off, hold the hose in a bucket and have someone else turn the stop valve on. Don't try and do it yourself. If you have good water flow and a new water inlet valve, it can only be the wiring or the control board / connections to it.
I hope that you ordered the correct part, Also there is an idler pulley that maintains the belt tension and that needs to be checked for proper tension.
The drain pump is clogged or not working. Some washers have belt-driven pumps - check the belt. If it is practical, unplug the washer and try turning the pump by hand (with the belt removed if it has one). If you can't turn it in either direction, it is jammed up or the bearing has seized.
If you need help identifying the pump, look online for appliance parts for your model. Most online dealers will have photos of the parts. The pump will be somewhere in the drain line from the tub to the drain hose.
Hi,
Please check that you added the softener to the correct compartment of your washer. Also, please read or re-read the instructions for adding the fabric softener. Once you've done those 2 things, please run a test wash with clothes that you would not particular care about potentially staining. Thank you.
Bad connection to power of the fill switch or not airtight to the hose on it.
E:FL - Fill Error - Pressure switch fails to open in 30 minutes in any fill agitate cycle.
the washing machine flashes "end" at the end of the programme
This is not a fault. The unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed. Distribute small and large items of washing in the drum. If required, spin the laundry once more.
https://www.youtube.com/watch?v=JAMGpceI6wc
Canon Printer Error E32 appears when your Canon Printer cannot find a wireless router during setup. There are a couple of reasons that restrict your printer from identifying a wireless network. If your printer is showing error code E32, most probably any wireless hardware is powered off. Else it is not working properly. Sometimes when your Canon printer is out of the scope network range, you encounter such error code. Most of the time, the wireless network need some time to setup and update. However it is also possible that the network that you are trying to connect with is hidden.
Devices like Printers make our work very easy & quick, even it's quite simple to use the printers these days because of the latest innovation & technologies that make printers much more efficient and easy to use. Well to Fix Canon Printer Error E32, a well-explained solution steps has been penned down by a team of Canon Printer Support technicians.
Follow the procedure to fix Canon Printer Error E32 -
SOLUTION 1 - Make Sure the Wireless Router is Turned On
First of all, you need to check that the WIFI that you are using is power on or not. It is the first & prime step. Make sure, all other connected devices are properly on and attached properly.
Check the WLAN LED indicator on your wireless router display. Make sure it is on & flashing too. Also check the on & off button. Do not forget to enable the Wi-Fi.
SOLUTION 2 - Keep your Modem nearby your computer system
Make sure the printer, the router and the system that you are using are in the same room. All the products need to be within the specified Wi-Fi range to build up a proper connection.
SOLUTION 3 - Turn on the Router & Wait
The wireless hardware takes some time to update properly. It requires 1-2 minutes to be turned on properly. Power of your computer & leave it for few minutes. And thus check if the network name is showing on the list or not.
SOLUTION 4 - Check whether the network is hidden or not
Also check the network that you are using to connect your printer with your PC is hidden or not. If it is hidden, you have to follow any alternative approach. You will need a different procedure to connect your printer with laptop or computer.
Hope, you are successfully able to Fix Canon Printer Error E32. But if you are not able to fix it by following the mentioned procedures, then you need to contact the Canon Printer Support Help-desk. The expert Technicians of Canon Printer are a highly skilled and certified profession and available 24*7 to assist you in your every issue related to Canon Printer Errors.
Most likely a bad lid switch preventing the motor from running. Ticking sound may be the timer (if it has mechanical, not electronic) control. Could also be a broken belt, but the motor would run (there would be some noise) it just would move anything.
