your information is NOT clear however, you must adjust the REED swtich, see the diagram, clean it, and tight the plug very well 2) RUN the software calibration, for diagnostic, troubleshooting, and fix it. 3) LUBE THE deck belt inmediately, maybe you have a worn deck belt, time to replace it.God bless you
Reset the machine. Take out the batterries. +reset the button machine+unppluged the power cord by 15 minutes.if this do not resolve the problem. RUN the software calibration for diagnose, troubleshooting, fix it.God bless you
1) please LUBE THE deck bel, this happen because the lack of maintenance, the machine is shutdown for enoug friction , this mean maybe there are deck worn.This shutdown for protect the electronic system2)LUBE the rollers bearings. too3) test the input voltage motor, if there are the motor need repair or replace.4) measure the output voltage board, for input voltage motor, if there are NOT the board is faulty.see the block diagram.God bless you
Dear Sr:Go to the the next web for download free your instruction manual:www.fitness.manualsonline.com or www.iconservice.com and follow the step for section troubleshooting. Normally the female and male connector has the same color, example red vs red. etc.If you have dout. go to www.sportsartamerica.com and download free the repair manual and see the color match.sincerely. God bless you.
Dear Sir:Go inmediately and buy a small piece of magnet in any Hardware.Since the key in any treadmill, is small magnet, and ready.sincerely. God bless you
Dear Sir:Please go to the next webs: www.manualsfactory. com + fitness.manualsonline.com + www.iconservice. com for free download.if you want pay try this www.fitnessrepairparts.com .sincerely. God bless you.Ernesto CuadraManagua, Nicaragua. c.a
Dear Sir:Since your equipment had been stoped by aprox 6 months.I will recommend 1) lubrication between deck vs walk belt very important.2) RUN the calibration software, this special design for to diagnose and troubleshooting the machine, is under Hood( see the instruction).sincerely. God bless you.attached: is my design for block diagram for treadmill for too diagnose and troubleshooting. ernesto a cuadramanagua, nicaragua. c.a.
hi, First of all you hve to check the speed sensor near the motor pully. Clean the speed sensor and check the treadmill. I the problem remains then You have to check the Driver circuit board for the motor. From your naration the motor is ok . Why the circut breaker trips because, if the IGBT( insulated gate bipolar transistor) is short then, when you press the start button the motor will try to drain a high current from the power line.IGBT controll the voltage to the motor.When it get shorted the applied voltage will go to the motor without regulation. Also you have to check the rectifier diode. The IGBT will look like one in the picture. Check the ohms between the seond and third pins of the IGBT. It should be above 1 kohm. Remember one thing remove power before oppening working in the treadmill. Because it have live area all over the driver board. ok
The motor controller board can be the issue.The motor is controlled by motor controller board.If the motor is replaced, and its new, then other possibility can be motor controller board.Also check, if the belt is getting stiff.Under the belt, there is greese oil, that makes it move freely.If this greese oil gets dried up, then belt will become hard stiff to move.Also it can be possible that motor controller board is got weak and its over heating the new motor, so its not running.------
Get the motor controller checked and replaced.-----------
This should help.Thanks.Helpmech.
The part number for the key is #208603. Phone the manufacturer at 1-800-753-4645. They can ship you one. The part is about $6, shipping is probably more.
hi
check the motor connection first. may have possibility of motor controlling igbt short or open. check the fuse in motor controlling card.also check the motor.
ok