Yes please see your instr. manual and follow the steps how to assembling and disassembling. if you do not have download for freefrom www. fitness.manualsonline.com God bless you
yes please read your instr manual and see the assembly instr and proceed according in reverse sense.if you do not have the instr. manual go to www.fitness.manualsonline.comGod bless you
you must have a Lamp for to help the screws. Unless the machine had not screws, must be adjusted to a pressure. You must use the screwdriver for to help to open the hood.see the video:
try to RUN the software calibration for diagnose, troubleshooting, fix it.2) LUBE THE deck belt , this happen because the lack of maintenance schedule, maybe the deck is worn and need replace it. see the video and picture3) lube the rollers bearing too very well.4) test the input voltage motor, if there are the motor NEED repair,tight any wires connector for loose5)measure the output voltage board, for input voltage motor, if there are NOT the board is faulty. use the DVOM OR VOM in both cases.see the block d, tight any wires connector or wires loosesGod bless you
Dear Sir:This problem is frequently.1) Check the breaker from your home and reset.2)Inspect the wires from your outlet in the wall and tight it.3)Do not use any extension cord!4)Examine the power cord and see if some wires is loose and tight it.5)Test the ground from your outlet wall, and fix it.6)Reset the c. breaker internal from the treadmill.7) Inspect any wires loose and tight it.8)Lubricates the treadmill between deck vs walk belt, this can cause to shut down the treadmill, since the complex electronic is designed for to protect the electronic components.9) Lubricate the treadmill in according with your manual instructions.10) The ball bearing from motor can be faulty+ball bearing from roller deck.11) The main motor board can be faulty. ( this is last step) sincerely. God bless you.ernesto cuadramanagua, nicaragua.
METAL ROTATING IN METAL: 2 MAIN PROBLEM :A) ROLLER BEARING + B) BEARING MOTOR.You hVE 2 OPTIONS: DO IT FOR YOURSELF B) CALL A SERVICE TECH.sincerely.ernesto cuadramanagua,nicaragua
1. Hold the upper end of the treadmill with your right handas shown. Using your left hand, pull the latch knob to theleft and hold it. Pivot the treadmill down until the frame ispast the latch pin. Slowly release the latch knobI will strong that you see your owner manual. If you do not have manual.here is the web page for you download free right now:http://www.iconservice.com/CustomerService/manualsProductManuals.do?model=EPTL88105&modelName=EPIC+425+MX+sincerely.Good luck.
Double check that all connections are secure, especially the console cable. Unplug and reconnect the console cable to verify.
Unplug treadmill from wall outlet. Wait 60 seconds, allowing lower board to discharge built-up energy.
Remove motor cover.
Verify that there are no lights lit on the lower circuit board.
Verify that all wires are securely and correctly placed on the lower circuit board, especially the large wire harness on the top of the circuit board with 12 different colored wires coming out of it.
1) Try to open the top consol.2) Spray with contact cleaner( from radio schack or computer store)3) Tight the flexible cable from keypanel vs display board4) Tight the connector from display board to Lower board( Main Controller Board)5) Test the main controller board.6) Test the transformer.Finally See the Block diagram that I did, you will see how the Main Controller Board has the 90% in any control. In that way you will have a good Strenght resultante, for to determine who is faulty. sincerely. Good luck.E.CUADRAMANAGUA, NICARAGUA. C.A
Oiling the deck of the treadmill with a silicone-based lubricant is an important aspect of routine maintenanceYou can buy online: www.fitnessrepairparts.comor www.gympart.comsincerely.E.CUADRAMANAGUA,NICARAGUA
http://www.youtube.com/watch?v=hHeYb6CoK4cPleae do it carefully to avoid any injury. Try that another person get involved, and use Belt for your self. Use some protect equipment gloves, plactic for to protec the equipment.sincerely
If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console. Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk.
Dear Sir:
I will try to help you, please go to the next web for download free:
http://fitness.manualsonline.com if you want to pay for owner manual. go to : www.fitnessrepairparts.com If you need further assistance, please reach me, sincerely. God bless you. E.CUADRAMANAGUA, NICARAGUA. C.A.
May existen 2 problem: a) Mechanical b) Electrical.
a) Mechanical: To due the shaft of Motor Lift bent, this cause to Stuch the motor, and produce some trigger of the breaker.Inspeccion it the shaft is o.k or is Bent.Change or Repair.
b) Electrical: 1) The breaker in the Board Controller can be dirty, or faulty, replace or repair. You can clean with special spray for contact.or use Ethylic Alcohol.
2) Check the rely or contactor for Motor DC, the contact will be dirty , clean and adjust it and replace or repair.
3) Check the continuity wire with VOM ( Range r x 100 from the Board control until the terminal of the Motor Lift DC is o.k or faulty, repair.
4) MEASURE the Voltage DC, with a VOM (VOLTIMETER) in range DC, approximately 48-50DC, if you can measure the same, the Motor is Faulty. You can Replace or REPAIR.
God bless you
E.CUADRAMANAGUA, NICARAGUA. C.A
