Epic 425 Mx Treadmill EPTL88105 ! - Answered Questions & Fixed issues


You need to replace the motor controller and walking belt.

Epic 425 Mx... | Answered on Aug 09, 2017 | 315 views


RUN the software calibration go under the HOOD motor see the instruction, and fix it. see the speed sensor7f016ade-041e-4f50-8a39-9f81109c1be9.gif
God bless you

Epic 425 Mx... | Answered on Jul 10, 2013 | 158 views


yes please read your instr manual and see the assembly instr and proceed according in reverse sense.if you do not have the instr. manual go to
www.fitness.manualsonline.com

God bless you

Epic 425 Mx... | Answered on Nov 25, 2012 | 83 views


Yes please see your instr. manual and follow the steps how to assembling and disassembling. if you do not have download for free
from www. fitness.manualsonline.com
God bless you

Epic 425 Mx... | Answered on Nov 21, 2012 | 282 views


1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the treadmill down until the frame is
past the latch pin. Slowly release the latch knob

I will strong that you see your owner manual. If you do not have manual.
here is the web page for you download free right now:

http://www.iconservice.com/CustomerService/manualsProductManuals.do?model=EPTL88105&modelName=EPIC+425+MX+

sincerely.Good luck.

Epic 425 Mx... | Answered on Oct 30, 2012 | 211 views


you must have a Lamp for to help the screws. Unless the machine had not screws, must be adjusted to a pressure. You must use the screwdriver for to help to open the hood.
see the video:

Epic 425 Mx... | Answered on Jul 30, 2012 | 628 views


try to RUN the software calibration for diagnose, troubleshooting, fix it.
2) LUBE THE deck belt , this happen because the lack of maintenance schedule, maybe the deck is worn and need replace it. see the video and picture
3) lube the rollers bearing too very well.
4) test the input voltage motor, if there are the motor NEED repair,tight any wires connector for loose
5)measure the output voltage board, for input voltage motor, if there are NOT the board is faulty. use the DVOM OR VOM in both cases.
see the block d, tight any wires connector or wires looses
God bless you
7_30_2012_10_06_51_am.gif7_30_2012_10_07_30_am.jpg

Epic 425 Mx... | Answered on Jul 30, 2012 | 313 views


Dear Sir:

This problem is frequently.
1) Check the breaker from your home and reset.
2)Inspect the wires from your outlet in the wall and tight it.
3)Do not use any extension cord!
4)Examine the power cord and see if some wires is loose and tight it.
5)Test the ground from your outlet wall, and fix it.
6)Reset the c. breaker internal from the treadmill.
7) Inspect any wires loose and tight it.
8)Lubricates the treadmill between deck vs walk belt, this can cause to shut down the treadmill, since the complex electronic is designed for to protect the electronic components.
9) Lubricate the treadmill in according with your manual instructions.
10) The ball bearing from motor can be faulty+ball bearing from roller deck.
11) The main motor board can be faulty. ( this is last step)

sincerely. God bless you.

ernesto cuadra
managua, nicaragua.

Epic 425 Mx... | Answered on Feb 15, 2012 | 157 views


METAL ROTATING IN METAL: 2 MAIN PROBLEM :A) ROLLER BEARING + B) BEARING MOTOR.

You hVE 2 OPTIONS: DO IT FOR YOURSELF B) CALL A SERVICE TECH.

sincerely.
ernesto cuadra
managua,nicaragua

Epic 425 Mx... | Answered on Dec 29, 2011 | 181 views


Double check that all connections are secure, especially the console cable. Unplug and reconnect the console cable to verify.
Unplug treadmill from wall outlet. Wait 60 seconds, allowing lower board to discharge built-up energy.
Remove motor cover.
Verify that there are no lights lit on the lower circuit board.
Verify that all wires are securely and correctly placed on the lower circuit board, especially the large wire harness on the top of the circuit board with 12 different colored wires coming out of it.

Epic 425 Mx... | Answered on Dec 09, 2011 | 139 views


1) Try to open the top consol.
2) Spray with contact cleaner( from radio schack or computer store)
3) Tight the flexible cable from keypanel vs display board
4) Tight the connector from display board to Lower board( Main Controller Board)
5) Test the main controller board.
6) Test the transformer.
Finally See the Block diagram that I did, you will see how the Main Controller Board has the 90% in any control. In that way you will have a good Strenght resultante, for to determine who is faulty. sincerely. Good luck.
11_28_2011_5_16_12_pm.gifE.CUADRA
MANAGUA, NICARAGUA. C.A

Epic 425 Mx... | Answered on Nov 28, 2011 | 180 views


Oiling the deck of the treadmill with a silicone-based lubricant is an important aspect of routine maintenance

You can buy online: www.fitnessrepairparts.com
or www.gympart.com

sincerely.

E.CUADRA
MANAGUA,NICARAGUA

Epic 425 Mx... | Answered on Nov 21, 2011 | 209 views


This happened to my treadmill. You need to get to the motor and see if the belt is fraying. If so, the fibers may have gotten entangled in the motor causing it to stay at the highest incline level. Once you clear this the treadmill will go up and down again. Hope this helps!

Epic 425 Mx... | Answered on Nov 20, 2011 | 500 views


http://www.youtube.com/watch?v=hHeYb6CoK4c

Pleae do it carefully to avoid any injury. Try that another person get involved, and use Belt for your self. Use some protect equipment gloves, plactic for to protec the equipment.

sincerely

Epic 425 Mx... | Answered on Nov 13, 2011 | 118 views


If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console.
Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk. 11_13_2011_11_53_47_am.gif11_13_2011_11_54_16_am.gif

Epic 425 Mx... | Answered on Nov 13, 2011 | 90 views


You should be able to just lift up the base and fold it into the supports,

Epic 425 Mx... | Answered on Nov 05, 2011 | 149 views


Dear Sir:

Will be a good Idea to replace with the original, and order to the Company.

sincerely.God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Epic 425 Mx... | Answered on Oct 24, 2011 | 121 views


Dear Sir:

I will try to help you. please be patience and carefully.

Watch the videos.
http://www.youtube.com/watch?v=yX_0vRPdMfU&feature=related
http://www.youtube.com/watch?v=H_ieEByRp34&feature=relmfu
http://www.youtube.com/watch?v=JhXR2BxOwWM&feature=related
http://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=related
http://www.youtube.com/watch?v=hKbAqvuOBS0&feature=related
http://www.youtube.com/watch?NR=1&v=USSgbsZbDLQ

How to Troubleshoot a Treadmill


Although most home treadmills are designed for easy operation, there are some common problems that are inevitable. The console may not display. Perhaps a loose or slipping running belt poses a safety hazard. Maybe the treadmill runs at an unpredictable speed. Those are just some of the things that can happen to bring your workout to a halt. While certain repairs will require the services of a professional who specializes in treadmill maintenance and repair, there are some basic repairs that you can do yourself.

Difficulty:

Moderate
Instructions

1.

    • 1

Clean and routinely maintain the running belt. The belt may be worn if the treadmill stops operating or trips the circuit breaker. Look for any tears in the belt. Test the belt by putting the treadmill at full incline. If it does not shut off, you may need to replace the belt. You can try lubricating it first, but the safest fix is simply to replace it.

    • 2

Tighten the running belt if it is loose. A belt can slip if there is too much friction. Be careful not to tighten the belt too much, though. You should be able to lift the belt at least 3 inches.

    • 3

Push the belt in the direction that it normally turns. Turn off the power before you start. If the belt is difficult to turn, there is high belt/deck friction. However, if the belt moves freely, that's not the problem.

    • 4

Examine the roller sleeve to see if it is centered on the running belt. If not, this could cause the belt to move to one side. Often a common problem with treadmills, you can try making adjustments yourself, but eventually you may need to replace the sleeve or roller.

    • 5

Stop the treadmill and immediately unplug the power cord from the outlet if you notice a burning smell. Overheating could be a sign that there is too much friction or a short in the wiring. Examine the belt and deck for any signs of wearing. If they check out alright, inspect the wiring. Replace any damaged parts as needed.

    • 6

Check to make sure that the power switch is on if you suddenly lose power. If this isn't the cause of the power loss, unplug the treadmill from the wall outlet and individually test the fuses, breakers and switches. Test the wall outlet first, as a fuse may have blown or a circuit breaker tripped.

    • 7

Allow the treadmill to run at a speed of 2.5 mph without anyone walking on it if you notice fluctuations in the speed. The speed should be constant. If not, there could be a problem with the motor.

    • 8

Test the motor using a fully charged lantern battery. The motor should still operate at slow speed.

    • 9

Replace the batteries in the panel if it dims. If the batteries aren't the problem, check to see that all the wiring is still intact. Sometimes a wire pulls loose.
With this you can fix it.
If you need further assistance, please reach me. sincerly. God bless you.

E.CUADRA
MANAGUA, NICARAGUA.





Epic 425 Mx... | Answered on Oct 24, 2011 | 169 views


Estimado amigo:
Le saludo y le recomiendo que lea cuidadosamente con paciencia y cuidado usted debera usar algunas herramaientas basicas.

Trate de ayudarle, vea tambien los videos.

Although most home treadmills are designed for easy operation, there are some common problems that are inevitable. The console may not display. Perhaps a loose or slipping running belt poses a safety hazard. Maybe the treadmill runs at an unpredictable speed. Those are just some of the things that can happen to bring your workout to a halt. While certain repairs will require the services of a professional who specializes in treadmill maintenance and repair, there are some basic repairs that you can do yourself.

Difficulty:

Moderate
Instructions

1.

    • 1

Clean and routinely maintain the running belt. The belt may be worn if the treadmill stops operating or trips the circuit breaker. Look for any tears in the belt. Test the belt by putting the treadmill at full incline. If it does not shut off, you may need to replace the belt. You can try lubricating it first, but the safest fix is simply to replace it.

    • 2

Tighten the running belt if it is loose. A belt can slip if there is too much friction. Be careful not to tighten the belt too much, though. You should be able to lift the belt at least 3 inches.

    • 3

Push the belt in the direction that it normally turns. Turn off the power before you start. If the belt is difficult to turn, there is high belt/deck friction. However, if the belt moves freely, that's not the problem.

    • 4

Examine the roller sleeve to see if it is centered on the running belt. If not, this could cause the belt to move to one side. Often a common problem with treadmills, you can try making adjustments yourself, but eventually you may need to replace the sleeve or roller.

    • 5

Stop the treadmill and immediately unplug the power cord from the outlet if you notice a burning smell. Overheating could be a sign that there is too much friction or a short in the wiring. Examine the belt and deck for any signs of wearing. If they check out alright, inspect the wiring. Replace any damaged parts as needed.

    • 6

Check to make sure that the power switch is on if you suddenly lose power. If this isn't the cause of the power loss, unplug the treadmill from the wall outlet and individually test the fuses, breakers and switches. Test the wall outlet first, as a fuse may have blown or a circuit breaker tripped.

    • 7

Allow the treadmill to run at a speed of 2.5 mph without anyone walking on it if you notice fluctuations in the speed. The speed should be constant. If not, there could be a problem with the motor.

    • 8

Test the motor using a fully charged lantern battery. The motor should still operate at slow speed.

    • 9

Replace the batteries in the panel if it dims. If the batteries aren't the problem, check to see that all the wiring is still intact. Sometimes a wire pulls loose.
http://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=related

http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=related

http://www.youtube.com/watch?v=GPI6dFJCUA4
http://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=related
http://www.youtube.com/watch?v=E5aWisfhT3Q&feature=related

Con esto usted debera reparar su maquina. Si necesita adicional asistencia, por favor contacteme.

Agradeciendole, Dios le bendiga.

E.CUADRA
MANAGUA, NICARAGUA. C.A.






Epic 425 Mx... | Answered on Oct 24, 2011 | 91 views


Dear Sir:
I will try to help you:

1.
Slow Walking Belt

o 1

Check that the surge protector meets the specifications listed in the manual.

o 2

Remove the key from the console.

o 3

Unplug the power cord.

o 4

Turn rear roller bolts 1/4 turn counterclockwise using an Allen wrench.

o 5

Keeping the walking belt centered, you should be able to lift each edge of the belt 2 to 3 inches.

o 6

Plug the power cord back into the surge protector.

o 7

Reinsert the key into the console.

o 8

Repeat the process if, after the treadmill has run a few minutes, the walking belt is not properly tightened.
2. Walking Belt Slips

o 1

Remove the console key.

o 2

Unplug the power cord.

o 3

Follow the same steps used for a slow walking belt.

See the videos:
http://www.youtube.com/watch?v=38w4PkiWIBY&feature=related

http://www.youtube.com/watch?v=yX_0vRPdMfU&feature=related

http://www.youtube.com/watch?v=E5aWisfhT3Q&feature=related
http://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=related

With this you will fix it.

If you need further assistance, please reach me, sincerely. God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.






Epic 425 Mx... | Answered on Oct 24, 2011 | 232 views

Not finding what you are looking for?
Epic 425 Mx Treadmill EPTL88105 ! Logo

74 questions posted

Ask a Question

Usually answered in minutes!

Top Epic Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Epic Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...