20 Most Recent Epic View 550 Treadmill - Page 9 Questions & Answers

Bad touch panel.That's why some work and others dont If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

RUN the software calibration for easy diagnostic and fix it.Go to the HOOD cover motor, and follow the steps , or use the owner manual for follow the steps.God bless you

see the video attached, lube the rollers bearing front+ back very well.2) the input voltage motor, if there are the motor is fault, see my pesonal TIPS.3) test the output of control board for input motor, if there are NOT voltage input for motor, the board is faulty.God bless you

Lube the Deck belt see the video attached. +LUBE too the rollers bearing front+back very well.This happen because the system protect the electronic system2) if the problem persist after you lube, you must test the input voltage for motor, if there are the Motor is faulty. see my personal TIPS3) test the output of the control board, for input to motor, if there are NOT the board is faulty.

please RUN the software calibration inmediately, for easy diagnose and fix it. However adjust the speed sensor, clean it, test for open or fraulty, tight the connector very well.God bless you

Dear Sir: Will be a Great idea that you connect with the next LINK and contact them.http://support.ifit.com/homeor You can download FREE your instr. manual and follow the steps very easy. go to www. fitness.manualsonline.comGod bless you

Hi, follow the instruction below....

• Hold down the "Stop" button, insert the safety key into the console and release the "Stop" button.
• Press the speed increase button to choose mph. An "E" will display representing English measurements.
• Remove the key from the console to exit the information mode.

1) Test the fuse or c. breaker see the diagram attached.2) Test the c. breaker from your hourse, or blown fuse3) Test the main switch of the treadmill see how to do it4) Test the voltage input motor, if there are voltage the motor need repair.5) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.God bless you

You will need the model number in order to order the correct parts. Under the front cover there is a tech sheet. It will tell you the model number. The model numbers are usually on the frame, and can be found once the treadmill is folded up. Yours will be something like EPCL******.
It sounds like you may need a motor controller PCB. The motor might be defective, but they generally don't just stop like yours has...
The model number tag also has a phone number to call for service. They can send someone out to look at it if you require a technician..
1-888-922-4222

Go to this link.
http://www.iconservice.com/CustomerService/manuals.do
Find your model number. (located on the lower frame under the walk belt in th front)
Input the number and download it for free.
Thanks Tim

Probably a bad motor control board, possibly bad connection, less likely but still possible is bad console. Another possibility is that it's in demo mode and you forgot to attache the safety key, but anyone who has had this treadmill a while would notice that.

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/

Please check this link:https://www.google.com/search?sxsrf=ALeKk02D68ibDlpmqPFTdJFsPUAG8G7Hqg%3A1609823462652&source=hp&ei=5vTzX9vmJfG4mAXst4l4&q=assembly+instructions+for+wynne+home+gym&oq=assembly+instructions+for+wynne+home+gym&gs_lcp=ChFtb2JpbGUtZ3dzLXdpei1ocBADMgQIIxAnOgcIIxDqAhAnUIwSWIwSYPUXaAFwAHgAgAHwAYgB8AGSAQMyLTGYAQCgAQGwAQ8&sclient=mobile-gws-wiz-hp