20 Most Recent Proform Crosswalk 500 Treadmill - Page 3 Questions & Answers

download the owner manual for free www.fitness.manualsonline.comGod bless you

The Steps for Newer Style Console Calibration

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Run the software calibration for troubleshooting. Test the s. sensor for open or faulty .clean it and tight very well.

God bless you

proceed according. God bless you

1. You may have a belt and deck problem. Test by the following procedure: a) without the power on stand on the walking belt b) push the belt in the direction it normally turns c) if the belt is very difficult to turn (on most treadmill) this means that you have high belt/deck friction these parts will probably need replacement. On occasion, you may have already damaged the DC board if you have high belt/deck friction. If the belt walks freely, you have a different problem. 2. If it passes the belt/deck checks, you may have a DC board output problem. If the belt tests ok and you have a speed variation, try this test: a) Set the speed to 2.5 MPH. Let the treadmill run without anyone on the belt. Check to see if the speed is constant or if there is a variation. b) If there is no variation, step on the belt. If the speed slows down or speeds up, you may have an output problem on the DC board. This is the board that connects directly to the motor. 3. You may have a short in the motor. If you turn the machine on and have erratic speed, you could have a problem in the DC board or the motor or both. With a simple multi-meter, you can test on the continuity scale to see if you have a closed circuit between either DC motor lead and the common earth ground. You should always have an open circuit. 4. You may have a speed signal problem. Your controls on the upper panel send a signal to the lower electronics to help them set the appropriate speed. If there is a problem in the signal generator, the communication links, or in the feedback links, you will have erratic speed operation. a) Communications test- Look on the board for a flashing signal as you increase speed on the treadmill. Most boards have a signal feedback test light. If a LED flashes, your communication is ok. b) Feedback test- If your unit is equipped with an optical feedback (disk inside a sensor) you can swap the feedback unit with the incline (it is the same part on many Icon machines). If it tests ok, you don’t have a problem here. If it is a magnetic feedback unit, you can test continuity with a multi meter or replace with a new part to test. Many times passing a kitchen magnet in front of the signal will make a speed display on the console if the magnetic sensor is good.

Really, I have had my crosswalk for over 20 years. I can't complain. I am passing it on to my son and getting a NEW Proform treadmill. Their longevity has sold me.....

you must to return the parts and demand for the original part for your right treadmill, Otherwise you must waste your time and money. Be sure if you are doing the right with the machine, Test aNY Fuse,c.breaker , REED switch, sensor speed,. Test all connector tight very well included the ribbon cable for keypads for display board.

please replace the batteries, with the same type, and the same polarity2) clean the contacts batteries very well3) adjust the REED swtich, test it, clean it, and tight the connectorvery well4) tight the ribbon cables for keypads.See the block diagramGod bless you

1) test the batteries and replace if are NOT full charges2) replace with the same types like ALKALINES only3) see if there are NOT connect in WRON polarities4) clean the contacts batteries with c. cleaner5) tight the springs contacts very well. and tight the plug well.6) tight the ribbon cables for keypads and connectors and clean it from display board vs lower board see the b. diagram7) adjus the REED swtich, see the diagram , clean it and tight the connector well.God bless you

see this video and fix it. God bless you

go to www. fitnessreairparts.com or www.doctortreadmill.com or www.treadmillpartszone.comGod bless you

go to www.doctotreamill.com and look how to adjust it.God bless you

lube the deck belt, you have deck worn, proceed in according with the instruction manual maintenance. 2) check the drive belt and replace it if necessary and tight 3) tes the input voltage motor, if there are the motor need repair or replace 4) test the output voltage from main board, for input voltage for the main motor, if there are NOT, the board is faulty. Try if you can RUN the software calibration for diagnose and troubleshooting.sincerely. God bless you.

RUN THE SOFTWARE CALIBRATION FOR INDICATION OF DIAGNOSE AND TROUBLESHOOTING.test the fuse and replace, check the c. breaker and reset, tight any connector. and tight any loose wires, of course disconnect the power cord.sincerely. God bless you.