20 Most Recent Life Fitness 9500HR Next Generation Remanufactured Treadmill - Page 4 Questions & Answers

if it is a classic model ..... you open it is easy to remove the wires removed the aluminum plate where the transformer and capacitor also remove brackets this way you will see the diodes (D4015L and SCR´s 2N6507 and TIP110 ) buy them at a sale of electronic and install For this you need a cauting and solder or tin and finally reassemble the same way you remove Any question send me a E-mail [email protected]

replace the keypad you can find on www.gympart.com to make the change you must remove the screws that are behind the console and then lift the cover art display, Remove the keyboard damaged and then you put the new

Step one: remove the screws to calibrate allens belt in the opposite direction clockwise allens wrench 5 / 16 "
Step two: remove the screws above the deck allens wrench 5 / 32 "
Step three: with a flat screwdriver to lift the lever of the Idler belt and remove the drive belt motor pulley. be careful
Step four: remove the rollers carefully.
Step five: Remove the deck
Step Six: Remove the philips screw that holds the spray nozzle
Step seven: now carefully remove the belt. to install belt now repeat these steps from back to front Once installed you must calibrate or belt slack to avoid turning the screws slide the meaning allens counterclockwise you can start with a speed 1.5Mph and increasing to 4.5Mph any questions send me an E-mail to [email protected]

if it is a classical model 9500/9500HR/9100/9100HR can take the card to a qualified technician mail, you must open the controller and change the following components: D4015L (2) 2N6507 (2) TIP110 (1) and in the latter case there to change the IRGBC40S.
if you treadmill is the Next Generation you should buy new and can find on sportsmith.com

press stop and when the screan is still blank hold down pause until it the cousle comes back up and then tagel to managers mouds then enter then tagel to whare you change from english to what ever

Hi, there is a service bulletin for this problem.
1) perform a continuity test on the power cord between the earth pin at the plug and any exposed metalwork of the treadmill (say an exposed bolt). If you get a reading of less than 1ω - that is good. If higher than this, try another part of the treadmill or trace the cause.
2) Ensure the Power outlet has a good ground - Your electrician could verify this for you.
The most common problems are static buildup on the Striding belt caused by users wearing polyester and scuffing their feet as they are running. This causes static buildup which gets discharged through the user when they come into contact with the treadmill frame.
Happy hunting

Get back into System test hit enter it will automatically to a check once completed. Then go to Lift motor module Go to manual incline and go to maximum incline then to 0 incline then get out of system test unplug unit for about 30 seconds. Then plug unit in if this does not work the limit or home switch may be the culprit

Take the end caps and motor shroud off visually inspect the frame tension bolts to see if anything is bent. then loosen, ( count how rotation it took to loosen the so when tighten the belt up you won't have to guest at the tension ) the belt and edges of the belt to see if the weave is uneven this cause the belt to travel. If you can tip the treadmill on its side to inspect underneath to see if anything skewed. Take your time and observe the mechanical operation you may have the above a 1/2 a dozen time before you see the problem, other than that anything short of replacing the belt this my recommendation. Good Luck to you

I'm not 100% familiar with your specific model, but I have to assume there's a reset button somwhere on the main console. A reset should return it the original factory settings. If there's no reset try unplugging unit and waiting a couple of minutes before plugging it in again.

You can possibly try this site http://www.treadmilldoctor.com/Safety-Keys_18

I'm sorry to say that using the acid base solution destroyed your function pad and will need to replace. Any clean must be done with simple green or warm gentle soapy water. Contact Life Fitness1-800-351-3737 or Nation Gym Supply 1-800-496-7278 give Model and Serial Numbers. Either company will help you.

Unplug unit open the motor shroud and inspect all wire connections to see if any rodent activity may have occurred. They could have built a nest inside. If you spot and damage then I suggest you call a qualified servicer to further assess the unit. Call Life Fitness @ 1-800-351-3737.

Best place to start is to call Life Fitness and their # is 1-800-351-3737 they may have the board in stock keep your fingers crossed

Get a hold of National Gym Supply @ 1-800-496-7278 They can either repair or exchange the board

To get to the service menu start by pressing the pause button and keep it held down as you hit the clear button twice. The treadmill will reset and go into the service menu, and now you quite pressing the pause button.

This mean that you unit is not equiped with a receiver inside the treadmill. Some models that was an option. Polar is the only brand that works with Lifefitness. You may have a bad upper display board. You can buy a replacement for a small amount of money. I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

It will be one of three things: #1 faulty Wax/Lift circuit board that controls the lift motor,#2 the motor itself, or #3 a faulty home switch, which is the white plastic switch in the base of the machine which senses the home position or zero degrees elevation.

Every time I have gotten this message, I have had to replace the motor controller.

On that left side end cap has a liquid wax hose assembly with nozzle on/off switch, this is used to refill the wax bladder underneath the running deck for lubricating the running belt itself. their are 2 screws that hold the end cap you will see the nozzle make sure its turned off make sure hose connections are snug. If any cracks in hose replace accordingly.

You need to press and hold Pause,press clear twice. Continue to hold pause until the display reads SERVICE MENU. Press any up arrow and select SYSTEM TEST. then press enter in the desired mode,then the display will scroll automatically though available options. You want the first option which is SYSTEM COMM TEST hit enter upon do so it will perform test to communicate with all module within the treadmill. If a module does not respond to the upper console the a error message will display.