Reebok Vista Treadmill - RBTL13305 - Answered Questions & Fixed issues


This type of treadmills seem to have high probability of failure if you use the emergency cutoff switch instead of the power switch at the bottom.

My guess is by yanking the red magnetic safety switch, the induced current put a heavy load on the central controller circuitry, and over the time it damages the IC chips on that board.

There's a border-line failure phase before the controller goes completely dead, I realized this and stopped using the safety switch, it hasn't had any issue ever since.

Reebok Vista... | Answered on Nov 30, 2015 | 114 views


If you push start and the belt does not move then it seems like the is a problem. This problem may be the LCB.

Reebok Vista... | Answered on Dec 04, 2013 | 221 views


the machine can be stop and trigger the c.breaker or fuse+ and the motor can be overheating and eventually burn.
adjust the tension by 1/4" of deflection.
God bless you

Reebok Vista... | Answered on Oct 14, 2013 | 54 views


HI, make sure there isn't a short in the actual outlet wall socket. if the outlet wall socket is in good condition, this will confirm power board failuer.

You will need to replace the power supply board in this unit in this case.

Reebok Vista... | Answered on Aug 06, 2013 | 371 views


tes the reset button for open or faulty and replace. tight the connection, or see if there are some loose wires and resolder. and try again.
However you can reset disconnecting the power cord by 30 seconds. and try again.
God bless you

Reebok Vista... | Answered on Aug 04, 2013 | 268 views


I am having same problem. The console lights up but none of the button works, including TV and the fan.


I actually took everything apart, unplugged and re-plugged the connectors on the PCBs of both side of the console, it still didn't help. Looking at the electronic configuration, TV, fan, left and right panels are relatively independent. I believe the driver/motor module is still working, the most likely cause of this is the controller CPU.

Reebok Vista... | Answered on Jul 29, 2012 | 737 views


adjust the reed switch, see the diagram attached, clean, and tigh the connector very well.
Try to RUN the software calibration for diagnose and troubleshooting.

sincerely. God bless you
5_3_2012_7_56_46_am.gif

Reebok Vista... | Answered on May 03, 2012 | 490 views


Hello,

The only place to oil is under the walk belt. You dont need to worry about it. If you want to, you can order a kit from iconservice.com.

Hope this helps, Matt

If you need further help, I’m available over the phone at https://www.6ya.com/expert/matt_8dbc24bf722649ac

Reebok Vista... | Answered on Apr 14, 2012 | 327 views


Watch this Videos:

http://www.youtube.com/watch?v=38w4PkiWIBY

http://www.youtube.com/watch?v=ch6Mix_FV00


You should not adjustthese since they are preset. Tension can be affectedslightly by adjusting the tension of the walking belt but if you have a slippingproblem, the drive belt will require replacement. If yourdrive belt is too loose, it will slip on the front roller pulley or the motorpulley. If it is too tight, it will increase your amp draw to the point thatyou may have an electronics or motor problem. Due to this, it is better to beon the safe side and replace a drive belt rather than riskover tightening it. A drive belt is usually $29.99 or less while many parts youcan damage by over tightening can be more than $300.Additionally, too much tension can cause bearing failure in the motor and thefront roller and front roller pulley failure. It is better to err onhaving the belt a little too tight rather than too loose due to the possibilityof injury if the belt slips. Motor Belt Adjustment-Icon Units Do not remove any of themounting bolts to the motorthese repairs will require 2 9/16" wrenches andmayrequire two people to accomplish the repairs Before beginning this repair: Check to make certain that the drive belt requiresadjustment. Check out belt slipping instructions or with the motor cover removed,walk on the belt normally and try to stall the belt to make it slip. Be careful during this test. If theproblem is in the drive belt, eitherthe drive belt will stop when stalled or the front roller will stop whenstalled. If the motor, drive belt, and front roller continue to turn when thewalking belt is stalled, the problem is with the walking belt slipping on thefront roller. If the drive belt continues to turn but the frontroller stalls, you may have a broken front roller pulley. If you need further assistance, please reach me, sincerely G-d bless you.
E.CUADRA MANAGUA, NICARAGUA. C.A.

Reebok Vista... | Answered on Mar 07, 2016 | 457 views


Hi,
Try to tension the tredmill's belt. For that you need an allen wench. Watch the following video to adjust the running belt. All the treadmills uses the same way to adjust the belt.



Reebok Vista... | Answered on Apr 17, 2012 | 822 views


Icon fitness has them. Part Number 238678. $134.00 plus shipping.
Thanks,
Tom

Reebok Vista... | Answered on Sep 14, 2011 | 189 views


Dear Sir:

I will help you inmediately: Check the circuit breaker to see if it hastripped. If the reset/off circuit breaker has tripped, wait 5 minutes andreset.
    • 2
If the power cord is properly plugged in, unplugit and wait 5 minutes before plugging it back into the surge protector.
    • 3
Remove and reinsert the console key. 4)Remove the key from the console and UNPLUG THE
POWER CORD.
5) Next, remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
and the Magnet on the left side of the Pulley .

6)Turn the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8". If necessary, loosen
the indicated Screw , move the Reed Switch slightly,
and then retighten the Screw.
Re-attach the hood and run
the treadmill for a few minutes to check for a correct speed
reading.

Thank you in advance,blessing, if you need some additional assistance please reach me. sincerely.

E.CUADRA
Managua, Nicaragua. C,A

Reebok Vista... | Answered on Sep 13, 2011 | 313 views


Dear Sir:

I will help you inmediately.

SOLUTION:
a. Check the reset/off circuit breaker . If the circuit breaker has tripped, wait
for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.

c. Remove the key from the console and then reinsert it.

d. Make sure that the reset/off circuit breaker is in the reset position
.
e. If the treadmill still will not run, you MUST replace the complete PCB to due some electronic component is in ShortCircuit.(Reason for to blown the fuse or c.breaker.

You must provide Mark, Model,Serial Number. please contact the phone number:.CALL TOLL-FREE from the:
1-877-994-4999
www.reebokservice.com

I hope to help you. blessing , sincerely.

E.CUADRA
MANAGUA, NICARAGUA C.A.

Reebok Vista... | Answered on Sep 13, 2011 | 289 views


Let me know if you find a solution. I am having the same problem and cant figure it out. It turns on and will start but none of the other buttons work. Its so frustrating.

Reebok Vista... | Answered on Sep 13, 2011 | 658 views


Did you ever find a solution to this problem? My treadmill is doing the same thing.

Reebok Vista... | Answered on Jun 21, 2011 | 333 views


Some tips here, for Treadmill Belt Slipping:
1.- The walking belt may be too loose.
a) Contrary to some belief, we have never found a walking belt that has stretched out unless it is accompanied by the seam on the belt separating. If you have made recent adjustments, lubricated, or had repairs, a belt can slip if not tightened.
b) The belt can slip if you have too much friction or if the belt has been recently lubricated. Attempt to lubricate by using our World Famous Treadmill Lube or another lube compatible with your treadmill. If lube does not help your problem and you have exhausted all other possibilities, the walking belt is most likely worn out and must be replaced.
c) To adjust the belt, follow the instructions on our web site at the following link: NEXT POST
d) An overtightened walking belt can raise the amp draw of your treadmill, contribute to seam separation on the walking belt, or both, so do not overtighten the walking belt.
e) As a general rule, you should be able to lift the belt in the center on the side by approximately 2" to 3". As a general rule, if you cannot lift it by 2" to 3", the belt is too tight.

2.- The drive belt between the motor and the front roller may be slipping.
a) All drive belts tend to wear with age and will wear more quickly if not aligned properly. Tightening the drive belt according to the directions in your owner's manual may prevent slippage but we don't recommend it since it is easy to overtighten and this can damage expensive drive system parts- you are much better off replacing the drive belt. Some models are designed with a misaligned drive belt so the treadmill can use the side load of the drive belt to reduce operating tension. These will always wear out quickly.
b) Treating the drive belt with belt dressing, which can be found on our site, will help the drive belt if slipping and will help prevent cracking and splitting of the drive belt.
c) If slipping of the drive belt persists after following these steps, the drive belt must be replaced. We sell most styles of drive belts. The information printed on the drive belt will usually be all we need to provide a quote.
d) An overtightened drive belt can raise the amp draw of your treadmill, contribute to bearing failure in the motor or rollers, or both, so do not overtighten the drive belt.

3.- The pulley on the front roller may have lost its grip on the front roller.
a) With the treadmill off, put a small piece of colored tape on an area of the pulley that you can see and put a corresponding piece on the roller tube. You can also use a colored, permanent marker like a Sharpie and draw a line from the pulley to the metal roller tube. Turn the treadmill on and while being careful, test to see what happens when the belt slips. If the drive belt and pulley continue to turn and the walking belt and front roller stop, the pulley has lost its grip on the front roller. If you couldn't see the pulley slip, compare the tape or the line. If the portions of the tape or colored line are still aligned, the pulley did not slip. Misalignment of the line or tape shows that the pulley and roller tube are not turning together and a failure of the pulley mount. This can be repaired or you can replace the roller.
b) On DP, Roadmaster, and Vitamaster treadmills, we will need a physical measurement of the roller. On all other makes and models, please provide us with the manufacturer and model number for a quote.

continue...

Reebok Vista... | Answered on Oct 13, 2013 | 591 views


Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Reebok Vista... | Answered on Aug 14, 2010 | 99 views


Check the main harness running up to the console through the leg. unplug it and use a volt meter to test the red and black wires. You should have 9-12 vdc if you do and the console is not lighting check that the safety key is in place. If it is and it is still not coming on the console is malfunctioning and would need replaced. If there is no voltage coming through the harness then you will need to check the harness for continuity. If harness tests ok then the controller is malfunctioning and would need replaced.

Reebok Vista... | Answered on Aug 11, 2010 | 164 views

Not finding what you are looking for?
Reebok Vista Treadmill - RBTL13305 Logo

82 questions posted

Ask a Question

Usually answered in minutes!

Top Reebok Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Christopher DeSantis

Level 1 Expert

3 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Are you a Reebok Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...