Reebok Vista Treadmill - RBTL13305 - Page 4 - Answered Questions & Fixed issues

Manual for sale online - $14.99 http://userguides.50webs.com/reebok_tr2_manual.html

Rather than this being a belt lubrication proble, which is what this error means on some treadmills, for your brand, I believe the following applies. E01: This indicates an interruption of power between the power in socket and the console. Check all wires at the base of the right arm are connected. If so, contact technical support. A link to such follows. https://www.reebokfitness.info/support

notify reebok

You need a new control board - around 65 UK pounds from Reebok (in uk) and pretty easy to fix. Remove 4 screws from plastic motor cover and remove cover. Loosen the circuit board hold-down screws (x2) then take phone/ipad photographs of board connections to aid re-assembly. Disconnect the 6 or 7 leads from their spade connectors. Fit new board, reconnect the leads in the same place using the photographs then, fit the two board retaining screws and replace the cover and 4 screws. Job done!

https://www.youtube.com/watch?v=qbAovLIcc4s This is a link to the instructions

I have a problem with my reebok i walk i run treadmill. The belt does not move on the lower speeds and after using it there is a burning smell even though it is working fine once I get past the first two speeds. I have had it 2 years but have never oiled it as I am not sure how and where.

Your treadmill may not be turning on due to a broken or a failed power supply or a broken power cord or a tripped circuit breaker switch a failed circuit breaker switch a bad power switch or wiring failure or a bad motor control board or failed console display screen can stop the treadmill from turning on. If the outlet is not working try to reset the house circuit breaker which is located inside of the fuse box to restore power to the outlet.

Loosen, but do not completely remove the idler bolts (on the back where you get on). Remove the side rail and motor hood (left side usually). While turning the drive roller by hand, pull on the inside of the belt in order to walk it off of the drive roller pully. Remove the belt and put the new one in.

E01 error code: communication failure: console board and control board cannot communicate.probably console board issue or control board issue or data cable issue. replace a data cable,checking whether the machine can running? If no, Replace the control board.

Check the low voltage supply, that is what supplies the 'brain' and display.

You failed to mention your question.

Contact Reebok directly to request the schematic diagram.

Request the wiring diagram from Reebok.

Error code E05 indicates a problem with the belt speed. Unlikely it is a bad sensor given the smell and heat. Hopefully it is under warranty. There are troubleshooting tips is the user guide. Here is an assembly model that serves for both the ZR8 and ZR9. The following indicates how to adjust speed and lubricatrThe first one may help narrow down the problem but the others may prove more helpful. If adjustment does not help, you likely will have to try a service tech. https://anytreadmillparts.com/pages/treadmill-error-code-troubleshooting https://www.sportsrec.com/351318-how-to-troubleshoot-my-reebok-treadmill.html https://www.manualslib.com/manual/1064934/Reebok-Z9.html https://www.youtube.com/watch?v=OFn0aVzkFlE

Contact Reebok directly to request the diagram.

Loose or broken parts under the motor hood of your treadmill can cause the machine to not start. If the console lights up, but the treadmill won't start, the motor controller could be damaged. Loose wires under the motor hood or in the console can cause your treadmill not to start.

This is a tedious process. Leave one of the adjusters where it is and adjust the other side until the belt starts to move to the center. This has to be done with the treadmill moving the belt so that the belt can move into position. Once the belt is in a central position, then you turn the adjustment screws one half of a turn on each one until the belt is tight enough.

If you wish get some details about treadmill repair check the link below www.electro-medical.blogspot.com

Rebock zr9 treadmill is working but cant see the screen

check and test safety [kill ] switch- circuit - motor