Reebok 8050 ES Treadmill - Answered Questions & Fixed issues

You must measure the 110Vca, Forward and backward. 2) If you do not have the l. switch can be faulty, measure for continuity. 3) Be sure the capacitor for this is Good. look for some wires loose, Retight. Blessing [email protected] cell+whatsAPP:+50588611441

If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) above the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.If you still have slipping then the drive belt under the motor shroud can also cause this problem unplug unit remove shroud then plug unit in start it up observe the front roller to see if it stops if it does locate the tension adjusting bolt by the motor loosen motor mount and proceed adjusting until slipping has been eliminated

Maybe check for a reset button around the motor/ belt drive. Manually roll the belt a little to free up motor if it's been sitting awhile.

That belt needs to be adjusted so it does not slip under load.

see the videos and fix it. God bless you.lube the rollers bearing front+back , test the drive belt motor, and replace it if necessary.

GO to www.iconservice.com give your model, and download for freeor go http:// fitness.manualsonline.com for free downloadsincerely. G-d bless youernesto cuadramanagua, nicaragua c.a.

PLEASE BE SPECIFIC?

treadmilldoctor.com

Look for a repair person in your area. Se Treadmill Repair Directory

You mean front- to-back or side- to-side?

If its side to side, adjust the allen bolts at the bottom front of the treadmill. If its front to back, and your treadmill is at least a few years old, the belt is probably stretched and needs replacing. You can get a quote for a new belt at http://www.treadmill-world.com/parts-manuals.html

You can order it at iconservice.com If you need further help, I’m available over the phone at https://www.6ya.com/expert/matt_8dbc24bf722649ac

You can order a belt at Treadmill Parts

They cost $100 - 200 and come with instructions for you to install yourself.

If the treadmill is a Reebok 8050 they have manual for it at iconservice.com. This compamy manufactures a wide variety of treadmills and the only way for sure to find the correct manual because they have the assembly instructions that canbe useful in the disassembly procedure.
Reebok

• For questions about parts, service, user's manuals or non-working products for Reebok Home Fitness equipment, please call our Reebok Customer Service Department at 1-877-994-4999.

If it's like many treadmills there should be 3 or 4 phillips screws across the front of the motor cover and 2 or 3 underneath. If this is a fold up model, tip the top front back to the walking board. Use your foot as a brace to keep the unit from sliding when you tip it backwards. You now need a # 1 and 1/2 or 2 10" phillips screw driver as the screws that hold the hood down are recessed. On some models there is a screw going thru the underside of the right and left side of the frame. If this is the case, you can fold up the walking deck to see them.

In order of most likely cause. 1) Worn motor belt needs to be changed. Rear roller bolts need to be tightened as the walking belt has too much slack(2-3 inches lift on the edge of the belt in the middle on each side) 3) the nylon pulley on the front roller is slipping and a new roller is needed.

check the motor controller for shorts and also check the ground wires

If you do not find a solution i have a faulty screen and require a replacement cheersb andy

go to iconservice.com go to manual input this info RBTL071070 - REEBOK 8050 ES TREADMILL a manual is their to down load.

Hi James
Unplug unit remove motor shroud then plug unit back in , press start and begin walking on the belt normally and try to stall the belt to make it slip ( planting foot to stop the belt).
Be careful during this test. If the problem is in the drive belt, either the drive belt will stop when stalled or the front roller will stop when stalled. Here is the procedure for adjusting the drive belt.
Find the motor mounts. Many motors in Icon treadmills have a main pivot joint in which a bolt runs the full length of the motor mount. This bolt will require loosening to provide maximum adjustability. Some models have a single jack bolt and others have an auto tensioner. Single jack bolts are the easiest to adjust.
Find the set bolt(s) on the motor. This is typically run through only one side of the motor mount or may be on both sides but it does not run the full length of the mounting. Loosen this bolt(s) but do not remove. Jack bolt models will have flat mounts and may contain up to four bolts.
Look for a bolt that will tension the motor. If it has this bolt, it typically runs in the same direction parallel with the drive and walking belts. If your treadmill is not equipped with this bolt, skip to Step 4. If your treadmill is equipped with this bolt (very few are) the repair will only require one person. Using 2 7/16" wrenches, make a few turns to this bolt, tighten the bolts and test your treadmill for slipping. If belt continues to slip, and if their is too much tension ( you should be able comfortably twist the drive belt 90 degrees ) then replace drive belt.
If the motor, drive belt, and front roller continue to turn when the walking belt is stalled, the problem is with the walking belt slipping on the front roller, here the procedure adjusting the walking belt.
If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn.When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened
If the drive belt continues to turn but the front roller stalls, you may have a broken front roller pulley. If this is the problem, you will notice it because the plastic will usually make a loud squealing sound on the metal front roller. The front roller assembly will need to be replaced and the drive belt must be replaced also. We suggest replacing the drive belt as well because it is a low cost item and will most likely, have suffered unusual wear from the problem. Another possibility is that the drive belt has worn down. In some cases, belt dressing may help correct the problem. If not, the drive belt must be replaced.

Go to iconservice.com click on manufacturer the model name you will find an owners manual so you can disassemble your unit