Proform XP Weight Loss 620 Treadmill - Answered Questions & Fixed issues

If the machine is over 7 years old then you need to replace the walking belt. Most proform treadmills are not meant to be run on, especially by anyone over 220lbs. Forget what the manual says, they are a terrible company.

Proform XP... | Answered on Sep 13, 2017 | 1,093 views

at first you must do a little relax your belt and reduce force on motor and check is it good or not .
you can countiue contact us with smart phone on wattsapp or telegram by :

Proform XP... | Answered on Apr 30, 2017 | 1,006 views

Dear Laura: I can recommend you to follow the instruction of your onwer manual, they have many instruction how to lose weight.
Of course the best if you have consult with some expert nutritionist.

God bless you

Proform XP... | Answered on Sep 15, 2016 | 173 views

If you wish to get some details; check the site linked here. Pull up older posts..

Proform XP... | Answered on Aug 09, 2016 | 55 views

If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

Proform XP... | Answered on Mar 07, 2016 | 903 views

Have you considered moving the doorway first? Or you could go with what all these other people are suggesting: turn up the speed and then ride it like a tank through the wall. If you have drywall you might slide right through. Please record the whole thing for the rest of us. We all need a good ab workout from laughing at the result.

Proform XP... | Answered on Sep 24, 2014 | 343 views

place a regular 9 volt battery to the motor wires with the unit unplugged from wall and see if it moves. if not it's the motor, if so it's the lower board. we can help with that @

Proform XP... | Answered on Feb 11, 2013 | 743 views

see the video and proceed according. God bless you

Proform XP... | Answered on Jan 31, 2013 | 256 views

Please RUN the software calibration for easy diagnose, troubleshooting and fix it.
Otherwise you must see the diagram attached and proceed according.Lube the motor and tigh any plug for the elevation motor
God bless you

Proform XP... | Answered on Dec 05, 2012 | 55 views

Try to tension the Walking belt. If the walking belt is not in tension then the belt will stop when you step on it. Watch the video to find how to tension the walking belt. Every treadmill follows the same procedure.

Proform XP... | Answered on Sep 27, 2012 | 288 views

Hi Pstefanski..Afraid there is no easy fix to this problem..I had the same also..I called Sears and for the cost of replacing the keyboard, it would be cheaper to buy a new treadmill..keyboard was close to $300 ..depend how old it is to tellu the truth..AL

Proform XP... | Answered on Mar 18, 2015 | 1,893 views

1) Lube inmediatey the Deck belt,according with the instruction manual
2) Lube the rollers bearing according with i. manual
see the diagrams attached.
3) Run the software calibration for easy diagnose, and troubleshooting. God bless you

Proform XP... | Answered on Jun 03, 2012 | 100 views

Dear Sir:
1) Test the c.breaker inside and reset.
2) Test the fuse inside and replace use de DVOM for continuity
3)Tight any connectors wires very well.
4) See inside if there are some wires loose and tight.
5) Adjust the reed switch, clean and tight the connector very well.
see the diagram attached.
See my personal TIPS for HELP

sincerely. God bless you.

Proform XP... | Answered on Nov 19, 2013 | 242 views

Dear Sir:
Please RUN THE software calibration for easy diagnose and troubleshooting, and adjust the speed sensor see the diagram attached.
And you will see the problem with the motor, possible lack of LUBE, and maintenance.Now you test the motor for lubrication and maintenance too.


Proform XP... | Answered on Apr 21, 2012 | 133 views

adjust the sensor switch first.2) change the batteries if have it.3)tight the flexible cable vs display board.4) tight the connector from display board vs lower board.
If the problem must test the following:1) Test the main motor.2) See if the drive belt is broken, loose, or slip3)finally the main motor board possible is faulty
see block diagram12_1_2011_11_16_04_pm.gif12_1_2011_11_16_27_pm.gifgood luck.

Proform XP... | Answered on Dec 01, 2011 | 373 views

Some consoles require batteries. Check to see if this is the problem. If the console does not use batteries, move on to Step 2.

    • 2

Remove the key from the console.

    • 3

Unplug the power cord.

    • 4

Remove the screws from the console hood and remove the hood.

    • 5

Turn the pulley until the reed switch and magnet are aligned with a 1/8-inch gap between reed switch and pulley.

    • 6

Replace the hood.

    • 7

Plug in the power cord.

    • 8

Reinsert the key into the console.

    • 9

Run the treadmill to check for a correct speed reading. This may take a few minutes.

Proform XP... | Answered on Nov 28, 2011 | 202 views

1) You must try to check if some wire from speaker are loose, corroded, or making
bad contact.

2) See carefully if some wire from the cone of the speaker is bad solder.

3) Of course you must open the cover for to get insider to the speaker.
4) Connect other devices for to test the speaker again, in order to avoid any bad devices before connected.
5) Finally if happen the same thing , you will have amplifier faulty. See the block diagram attached.11_28_2011_5_31_44_am.gif

Proform XP... | Answered on Nov 28, 2011 | 166 views

  • Place a mat under your treadmill. You can buy a treadmill mat at any sporting goods store and most major discount stores such as Wal-Mart or Target. Treadmill mats are made of heavy-duty rubber or foam and are specifically designed to absorb the vibrations caused by the everyday use of a treadmill. Treadmill mats greatly reduce the noise caused when a person runs on a treadmill, and are especially helpful if you live in an apartment and have neighbors immediately below you.
  • 2 Tighten or replace the belt on your treadmill. A loose or worn belt will cause your treadmill to vibrate excessively. You can buy replacement belts at many sporting goods outlets or directly from your treadmill's manufacturer. Refer to your user's guide for instructions regarding how to tighten or replace the belt, as well as the size and type of replacement belt required by your treadmill.
  • 3 Secure all ancillary parts of your treadmill. Be sure that the rails, console and housing are in place and fastened tightly to the body of the treadmill. Tighten any loose screws or bolts

  • Additional: Level the machine with a good level 2) put a little oil to the shaft of incline motor c) to line up the incline motor

    Proform XP... | Answered on Nov 16, 2011 | 219 views

    Not finding what you are looking for?
    Proform XP Weight Loss 620 Treadmill Logo

    158 questions posted

    Ask a Question

    Usually answered in minutes!

    Top Proform Exercise & Fitness Experts

    Ross Metcalfe
    Ross Metcalfe

    Level 2 Expert

    135 Answers

    Android Man
    Android Man

    Level 2 Expert

    278 Answers

    jay kaye
    jay kaye

    Level 3 Expert

    305 Answers

    Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides