Proform CrossTrainer Treadmill - Answered Questions & Fixed issues


Please LUBE very well the Screww with WD-40 and wait for 30 minutes.
And try again. Use the common sense to take out the screw with the electric driver.
Blessing.
cuadra2016@yandex.com
cell+whatsAPP:+50588611441

Proform... | Answered on Nov 24, 2017 | 327 views


see the diagram attached and fix it. God bless you

83d26120-fbb3-449f-acb9-5bcec9455150.jpg193117b1-28fd-4a03-9766-27c03886d5ee.gif

Proform... | Answered on Dec 10, 2013 | 227 views


see the video and fix it. God bless you

Proform... | Answered on Feb 08, 2013 | 38 views


Sounds like a lower motor controller, that would be the first part I'd replace. Be aware that treadmills have a high power draw and if you are also running other power suckers on the same circuit, the low voltage tends to short out the console or the control board.
The control board is easy to get to, and cheaper to replace than a console, but not cheap. You can also call the 800 number on the front of your owner's manual and they may help you diagnose it.

Proform... | Answered on Feb 06, 2013 | 185 views


please adjust the REED switch, TEST for open or faulty, clean it, and tight the plug or connector very well, see the diagram attached.
2) Tight the ribbon cable inside very well for keypads
3) replace batteries with the same types, same value, same polarity, and clean the contacts batteries.FULL charges.
God bless you
12_7_2012_3_44_21_pm.gif12_7_2012_3_44_52_pm.gif

Proform... | Answered on Dec 07, 2012 | 193 views


1) This happen to due the lack of maintenance schedule Normally you must lube after 5 hours of use. So this system protect itselft a shut down. Now you must have a WORN DECK BELT, time to change. it

2) LUBE the rollers bearing

3) Test the bearing from main motor, replace
God bless you
11_15_2012_12_52_45_am.gif

Proform... | Answered on Nov 15, 2012 | 107 views


I do not see the problem, download your manual instruction and go to the troubleshooting area. go to www.fitness.manualsonline.com

God bless you

Proform... | Answered on Aug 29, 2012 | 183 views


1) You must RUN Inmediately the software calibration for easy diagnose and troubleshooting and fix it.

God bless you

Proform... | Answered on Jun 27, 2012 | 34 views


Dear Sir:

Inside test the fuse and replace use DVOM, or reset the c.breaker

2) Adjust the reed switch see the diagram attached, clean,and tight the connector very well. Tigh the ribbon cable from keypad + connector from display board vs lower board

3) Lube the deck vs deck belt, this produce enough friction.

4) test the input motor voltage,if there are the motor need repair or replace

5) Test the output voltage from the m.motor board for the input motor voltage, if there are NOT the board is faulty.

6) Try after your fix, the software calibration for diagnose, and troubleshooting.

sincerely. God bless you
5_2_2012_10_06_22_pm.gif

Proform... | Answered on May 02, 2012 | 240 views


Question: which breaker is tripped? 1) breaker inside of the machine or 2) breaker froom your home?

Proform... | Answered on Dec 12, 2011 | 216 views


Dear Sir:

Hello, I hope everything is fine.

I will help you inmediately.
Things You'll Need
  • Pencil
1.
    • 1
Switchthe power off without unplugging the machine. Do not take the safety key out ofits place.
    • 2
Inspectthe bottom of your console. The calibration switch is in a small hole. Insertthe eraser end of a pencil into the hole and softly push the button. You willsee CL11 on your console after you push this button.
    • 3
Usethe Speed + or - key to select MPH or KPH. Push the Power key to save yourselection.
Thank you in advance, sincerely. God bless you

If you need further assistance, please reach me.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Proform... | Answered on Sep 28, 2011 | 174 views


Dear Sir:
Thank you by your question, here some answer:
PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet . Use only a single-outlet surge suppressor that meets all of the specifications . Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is inserted into the console. c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes.and then press the switch back in. d) Please check the power cord maybe is broker Testign with DVOM(Digital Voltimeter). e) Test the circuit breaker of the House, and Reset, see in outlet box if some wiring is loose.
Thank you in advance, sincerely. Blessing.
If you need additional Help, please contact me.
E.CUADRA Managua, Nicaragua.

Proform... | Answered on Mar 08, 2014 | 309 views


There are Allen bolts on both sides of the base, on the end away from the console. Turn one bolt one way the other the other way to move the belt from side to side.

Proform... | Answered on Aug 12, 2011 | 77 views


This is probably not your ideal solution but just in case it is helpful here is a list of the models of the proform crosswalk 405, if you select your exact version you can purchase a new owner's manual.

Proform... | Answered on Jul 20, 2011 | 212 views


Depending on which version you have (last digit after the model #), you can click on your specific version here to purchase a printed manual for the ProForm 831.29730.. if you can't find one for free online.

Proform... | Answered on Apr 27, 2011 | 206 views


Here you can find parts for a lot of Proform equipment. I would try to find your specific model there and see if they have it.

Proform... | Answered on Apr 12, 2011 | 23 views


which roller, name of part . look in the back of your manual

Proform... | Answered on Mar 09, 2011 | 26 views


check the tension on the w/belt if good or still slipping then its your motor belt

Proform... | Answered on Mar 09, 2011 | 82 views


hi,
your treadmill's belt is loose. You have to tight the belt from the both side.
all the treadmills follow the same procedure for tightening the waking belt. Watch the following video for the same.
ok

Proform... | Answered on Mar 05, 2011 | 92 views


Your belt may be too loose, or you may need your deck re-lubricated.

Proform... | Answered on Mar 01, 2011 | 286 views

Not finding what you are looking for?
Proform CrossTrainer Treadmill Logo

144 questions posted

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

jay kaye
jay kaye

Level 3 Expert

305 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...