Top 20 Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher Questions & Answers

check that the drain pipe is not blocked or has a bend in it as this will stop water passing easily, remove and blow down pipe to make sure its clear. (wash out mouth afterwards) if this is fine then the pump must be weak or something is stopping its movement. if it is the pump you will need to remove it from washer and open the pump up by the 3 screws and remove the propeller and clean out the housing and pump parts, should be magnetic type and easy to fix. build up of food debris can limit the pump from moving.

the spinner arm itself may be blocked..............remove arm and check hold are clear.......... cheers

it means it cant feel if any water is entering the machine. either due to the water being turned off somewhere , the inlet hose not connected or the inlet flow sensor has failed

Either the heater unit or the dryer fan is faulty.

Check that you have not been using the Eco wash cycles.

Also make sure you are using the detergent and rinse-aid recommended in the dishwasher manual.

Hi,

It's fairly easy but you need to remove the front panel of the door first. To do this you will need a T20 T-Star screwdriver or screwdriver bit then follow these instructions:

1. Open the door and fold it down flat - there are 10 screws (T20) around the edges of the door
2. Undo and remove the 3 screws on each side - leave the 4 screws at the top!
3. Close the door
4. Grab the door at the bottom on both sides and pull gently towards you about 2-3 inches.

At this point you may find that 2 plastic clips fall out. Don't panic - it's not broken. They slide back on when the panel is removed.

5. When the bottom of the door is pulled away, pull it downwards and it will slide out from behind the control panel. The outer panel of the door should now be completely free.

You will now be able to see the back of the detergent compartment where the springs are located. Re-attach the springs, then re-fit the door following the instructions above in reverse order. If one or both of the clear plastic door clips have come off, reattach them to the brackets at the bottom of the door before re-fitting the panel. It's much easier this way!

T-Star bits are freely available - I've attached a picture of one.

If you get into any difficulty removing or refitting the door, please post back and I will assist you further.


Please rate this solution if you find it helpful. Thank you.

100% fact. But people would not agree. Some times the washing machine left un attended, it will become a walking machine during spin cycle.

Contact the service provider and get appliance inspected. It could any thing!

Hi,

Please help us ellaborate the issue so that we can assist you better.

Waiting for some more info.

Thanks

problem on the safety switch
1)try to adjust the safety switch to contact properly with the door.
2)any screw is there on switch means loosen the screw &adjust to contact with door.

create an inverted trap in ther dishwasher drain line so the water cant back feed

This is the parts schematic that shows all the parts and where they are located. The noise is either something stuck in the pump or a dry bearing. https://www.searspartsdirect.com/model/25b4iqte9a-001794/bosch-she58c02uc-50-dishwasher-parts ..

Dishwashers come in standard sizes. Your old one is 60 CM wide and made for built in. https://www.bosch-home.ca/en/supportdetail/product/SGU4025AU/31 DISHWASHER 60 CM BUILT-IN/BUILT-UNDERSGU4025AU/31 As long as the new one is also for built in, the dishwasher will fit. Measure the height of the space you have. There may be a little height adjustment on the feet. ..

That is just saying the Child Lock (CL) has been activated.

Deactivate the child lock ' Bosch

Bosch Home https://www.bosch-home.com > ... > Get support 1. Press and hold the start button for three to five seconds ... When the child lock is activated, there will be a message "CL" in the display and all the washing ...

Bosch dishwasher child lock problem

Bosch-home.co.uk https://www.bosch-home.co.uk > ... > Dishwashers Hold down the lock button for three to five seconds. You should hear an audible beep and/or see the symbol disappear. The child lock is now deactivated.

What does CL mean on a dishwasher? And how do I fix it?

Quora https://www.quora.com > What-does-CL-mean-on-a-dish... This code means that the CHILD LOCK or CONTROL LOCK feature has been activated. When activated, all buttons will not change except the washer's door and the ... 9 answers · Top answer: First, look on your dishwasher to find a label that shows the manufacturer and the model number. ...

How to turn off the CL on the display of a bosch dishwashe...

JustAnswer https://www.justanswer.com > Appliance Repair Oct 28, 2010 - You should just be able to just turn the power button off, then turn it back on and the CL should be gone. 1 answer · Top answer: Hello, and thank you for using this service. I'll be helping you with your ..https://www.youtube.com/watch?v=Xr4DBwACUW4

AI Bot Answer Deleted. In the base of the dishwasher above the floor there is a plastic tray that has a leak sensor. If you see water behind the machine than it means you have a 'spraying leak' as the sensor cuts off the machine as soon as it is triggered. It is likely to be a leaking hose on the pump. It can also be caused by the machine over-filling. An E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated. What can I do to fix the E15 Error Code on my dishwasher? Please turn off the water inflow and contact Bosch Customer Support for assistance.

E15 Bosch Dishwasher Error Code

Check if there is anything in the large item trap or blocking the water level sensor. The dishwasher won't try to fill if it believes it is full. Try pressing and holding the Start button for 3+ seconds. The Clean LED should light up in a minute. If it does, try the on/off button and starting a new cycle. (This just clears any old programs from the memory.) Some washers will stop if they detected a water leak. Sometimes turning off the power for a while and checking for water in the cabinet below the dishwasher or in the motor area is useful. The more likely items to check: Check the wiring between the inlet valve and the control board. Check the wires for corrosion at the connecting pins and for continuity. Broken conductors don't send a signal to open and close the valve. If those are okay, then the control board itself may be faulty. Since this dishwasher is discontinued by the manufacturer, I don't know if all of the parts are still available. The only parts list for the SHE3ARL2UC/28 that I found is here: https://www.partselect.com/Models/SHE3ARL2UC/ . They don't list any wires or the control board. I hope this helps. Cindy Wells

Add some salt.

It needs descaling. Try CLR in a wash

I have a Bosch Silence Plus 46 dBA. SHS5AVF6UC/22. ...

JustAnswer https://www.justanswer.com > Appliance Repair Jul 5, 2021 - What have you tried so far? When I try to start the cycle, the red light on the floor comes on, it beeps, but won't start. 1 answer · Top answer: Hi and welcome to Justanswer. My name is ***** ***** to assist you today. I'm Why is my Bosch dishwasher beeping and not starting? Bosch dishwashers are designed to beep when there is an error. A beep means that your drain is not clogged, and the rest of the parts are functioning as they should. Beeping in the middle of the cycle points to the problem with the control board itself. Find the circuit breaker and turn it off for 60 seconds.

Bosch Dishwasher Error Codes ~ By I-Fix Appliance Repair

The water supply is inadequate for your dishwasher.

The senors for your dishwasher are either dirty or need to be replaced.

https://www.reliableparts.ca/catalog/Touch-Up-Paints-467065 and Amazon of course!

Black Appliance Touch Up Paint

Amazon.com https://www.amazon.com > black-appliance-touch-up-... Rust-Oleum Paint 213174 .6-Ounce Specialty Brush Bottle Appliance Touch Up, Black, 0.6 Ounce. Enamel, Acrylic, Specialty. ..