20 Most Recent One For All URC-4330 Remote Control - Page 8 Questions & Answers

need code for zenith tv also

Unfortunately, your remote control predates TV/DVD combos and as such the manual does not list a code for a Sylvania TV/DVD combos.

To make this control work with a TV/VCR combo, one would enter 0054 for the TV controls and 0081 for the VCR controls. May I suggest you try the following codes for the TV: 0054, 0030, 0096, 0020, 0381. If these codes do not work, try running through the auto-code search.

The manual for the URC-4330 does not list any Sylvania DVD codes at all, so I recommend running through the auto-code search. Here are the steps:

1. On the remote control, press DVD once.
2. Press and hold SET until the LED blinks twice, then release SET.
3. Enter 9 - 9 - 1.The LED will blink twice.
4. Aim the remote control at the the DVD and slowly alternate between pressing POWER and DVD. Stop when the DVD turns off.
5. To lock in the code, press and hold SET until the LED blinks twice, then release SET.

Hope that helps.

There is only one code listed for Motorola cable box's, 1376.
If it doesn't work then your going to have to use the search through the internal memory of the remote. Below is a link to a web page of your remotes manual. Look under "Searching For Your Code" for the steps to do this. It's in .pdf format so you'll need Acrobat Reader if you don't already have it to view it.
Hope this helps.



http://www.oneforall.com/uploads/support/a75c4c2d67fdf305e4a8497cb64b60d0.pdf

SHARP
002 013 014 111 502 509 712 812 813 913 918
These are as close as i can get you
to getting you operations...the rest is up to
you. GOOD LUCK!

1. PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. ENTER the 3 digit code for your brand.
4. You should receive 2 quick flashes after entering your code.
5. PRESS the POWER button to test the code.
   

If you have tried all of the set-up codes for your brand of equipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.

1. PRESS the button for device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. ENTER 9-9-1 (two blinks on the remote)
4. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER)
   Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

Blinking Back the Code:

1. PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. PRESS 9 - 9 - 0.
4. PRESS 1, carefully COUNT the number of blinks. (1st digit)
5. PRESS 2, carefully COUNT the number of blinks. (2nd digit)
6. PRESS 3, carefully COUNT the number of blinks. (3rd digit)

If the remote DOES NOT blink it means the number is 0.
This is your 3-digit setup code.

The code for the Sanyo tv is 0154

http://www.retrevo.com/search/v2/jsp/downloadPage.jsp?doc=8897dd7b7cf5a779c8fadfaac54a3741&q=One+for+All+URC-3021

try this website

http://www.hifi-remote.com/ofa/devices-tv.shtml

check here...

get a new universal one

Here you go..

http://www.twirp.com/en/advanced_search.php

Rate well ;o)

most philips remotes can be programed using "code search" this is done by:
1: Manually turn on ur tv
2:hold setup untill red indicator stays on and release button
3: press and quickly release what you wanna program (i.e tv,vcr,ect.)
4:press channel up repeatedly untill your t.v changes channels(up to 300 times) if you over shoot the channel change press down til it changes again.
5: press and release MUTE to install the code.

I tried every number code listed on the website for "Sears" and finally found one which gave me menu access. Some codes evidently work for some functions, but not for all.

http://www.oneforall.co.uk/us_US/support

Go to the link below. Select the model that you have then select TV then select Zenith then click on Submit


http://www.ofausa.com/en/advanced_search.php

Couple things to try:

On the remote - Press "Clear" button
May have to turn off CC in the TV menus. Try Menu on the remote and look for closed caption there.
If remote doesn't work, can try with buttons on TV itself to get into menu and turn it off.

Here's a link to the manual for that remote:
http://www.remotecentral.com/cgi-bin/files/rcfiles.cgi?area=other&db=devices&br=innovage&dv=universalremote&md=jumboremote&kw=&st=&ar=&dt=&so=&pg=1&file=others/innovage/jumbo-manual.zip

Here's the link to the manual for the remote with instructions on how to program the codes:
http://www.remotecentral.com/cgi-bin/files/rcfiles.cgi?area=other&db=devices&br=innovage

The Code for Apex tv is 214

Zenith 0039, 0000, 0209, 0033, 0479

PDF... http://www.hifi-remote.com/manuals/manual.shtml?URC-4330