Sportsart 6300 Treadmill - Answered Questions & Fixed issues

1) adjust the REED switch, test for open or defective, clean it, and tight the plug or connector very well.2) After you fixed RUN the software calibration for easy diagnose, troubleshooting. and fix it.God bless you

Unplug unit and check the motor brushes they maybe worn and need to be replaced call Sports Art Fitness customer service @ 1-866-709-1750 they will sell you the brushes

E1 usually refers to the speed sensor located near the motor that turns the belt. Try cleaning it. They can get dust built up on it and cause faulty readings. If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

go www.fitnessrepairparts.com God bless you

the power supply is receiving too low or higher currents.You must test this. Or you need to call the service tech. However try to RUN the s. calibration if you can. Otherwise reset the machine. and see the block diagrams attached.God bless you

proceed according and use common sense;God bless you

1) adjust the Reed switch, clean, and tight the connector very well.see the diagram attached.2) Tight the ribbon cable from keypads, very well, and clean.3) Tight the connectors from display board vs lower board.See the diagrams. God bless you

1) Lube the deck belt, you have possible deck belt worn. Proceed in according with the instruction manual maintenance.1a)inspect the drive belt and replace if necessary.2) Test the input voltage to the main motor if there are the motor need replace or repair.3) Test the output voltage from the main motor board, for input voltage motor, if there are NOT, the board is faulty.sincerely. God bless you

Dear Sir:Please read your instruction manual, if you do not have. go for free:www.fitness.manualsonline. com or www.iconservice. com sincerely. God bless you

disconnect the motor from the motor control board under the motor hood ( follow the wires from the motor) and turn the machine on. If it lights up ok then the motor is blown.

Incline calibration is necessary when: the display shows ERR7, the drive board incline error LED ( LED5) lights or the incline has extended beyond its normal rangeThe goal of calibration is to synchronize the incline set mechanically and electronically. Mechanical calibration sets the incline motor pipe to the 0% position. This happens when the red line on the thin pipe is even with the end of the thick pipe. Electronic calibration sets the variable resistor (VR) value to the 0% position. This happens when the voltage across the VR blue and green wires is 1.20 VDC.Readings of VR voltage (blue and green wires) should show around 1.20 VDC at the lowest position and around 3.80 VDC at the highest position. If the VR looses calibration or cannot be set to 1.20 VDC, replace the VR. If the incline motor gets voltage from the drive board but fails to operate, replace the incline motor set. If the incline fuse blows again and again, replace the incline motor set.

Go to SportsArt America.com click on support drop down and click on manuals click on owner's manuals scroll down treadmills and half way down you will find t6300 owner's manual

If you can walk on your treadmill but you get a burning smell from it, you have a bad problem and discontinue use immediately and unplug the treadmill.

Burning smells are most commonly associated with the following problems:

1) Very high belt/deck friction.

2) Short in the motor.

3) Short in the wiring or electronics.

4) Literally cooking the lacquer or cardboard core (on cheap machines) in the motor from belt friction or a drive system

obstruction.

Friction is the #1 cause of this problem. Many cheaper treadmills have a motor with a cardboard core (people wonder why we are so

down on cheap treadmills) and if the voltage and amperage through the motor heats it up sufficiently, it begins to smolder. If this is the

case, you normally have to replace the belt and the motor and inspect the deck. If the armature has cooked enough in the motor, you

also have to replace the motor.

If the belt and deck check out OK, check for a short in the motor. You can run the motor with an independent power source like a fullycharged

cordless drill battery to see if the symptoms are the same. Click on the following link for our motor test.

If the belt and deck check out and the motor is OK, then check your wiring and electronics for signs of scorching and replace the

appropriate part(s).

Watch this videos tips:http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motor

When I turn on the machine it beeps and reads Error 7 on the screen. Do you have a support phone number for Australia

Dear Sir:

Hello, I will try to help you, inmediately.

Please follow the next step:

1) Find the set bolt(s) on the motor. This is typically run through only one side of the motor mount or may be

on both sides but it does not run the full length of the mounting. Loosen this bolt(s) but do not remove. Jack

bolt models will have flat mounts and may contain up to four bolts.

2) Look for a bolt that will tension the motor. If it has this bolt, it typically runs in the same direction parallel

with the drive and walking belts. If your treadmill is not equipped with this bolt, . If your

treadmill is equipped with this bolt (very few are) the repair will only require one person. Using 2 7/16"

wrenches, make a few turns to this bolt, tighten the bolts from Steps 1 and 2 and test your treadmill for

slipping. If belt continues to slip, repeat Steps If a second attempt does not repair the problem

3) If you have arrived at this step, let's make sure you have a drive belt tension problem. With the motor cover

removed, walk on the belt normally and try to stall the belt to make it slip. Be careful during this test. If the

problem is in the drive belt, either the drive belt will stop when stalled or the front roller will stop when

stalled. If the motor, drive belt, and front roller continue to turn when the walking belt is stalled, the problem

is with the walking belt slipping on the front roller. If the drive belt continues to turn but the front roller stalls,

you may have a broken front roller pulley. If this is the problem, you will notice it because the plastic will

usually make a loud squealing sound on the metal front roller. The entire front roller assembly repaired or

replaced (see the help topic on replacing a pulley) and the drive belt must be replaced. We suggest

replacing the drive belt as well because it is a low cost item and will most likely, have suffered unusual

wear from the problem. Another possibility is that the drive belt has worn down. In some cases, belt

dressing may help correct the problem. If not, the drive belt must be replaced.

Please check this video:

http://www.youtube.com/watch?v=yX_0vRPdMfU&feature=related

http://www.youtube.com/watch?v=zXeHMWTcLUY&feature=related

E.CUADRA

MANAGUA, NICARAGUA. C.A

That should be a power related error. ensure that it is in a dedicated 20 amp socket. before you start it again. you may also get user manual here.

Click on the following link:

http://www.sportsartamerica.com/saf/support/technicalsupport/owners_manuals.asp

Select the 6300 Treadmill under COMMERCIAL PRODUCTS.

Save the file somewhere on your computer.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there.

Otherwise just unzip and open the file.

If this was at all helpful please click on the 4 Thumbs Up helpfulness rating icon you see on this page.

Thank you very much and good luck.

I'm getting the same E-6 error while running in program mode although the fuse is fine - and when I recycle power, the program starts fine again and then stops in the middle with the E-6 error. Nor sure what's wrong. Just sandpapered the fuse ends and the connector ends to the fuse socket. We'll see how it goes.

You are going to need a motor controller, or find someone who can repair the one you've got there.
If it blows the fuse immediately on power up, it may require a full wave bridge rectifier replaced on the controller. If it blows when the start button is pushed, it might be a MOSFET or SCR found on the motor controller..
Sportsart fitness can be reached by phoning 1-866-709-1750. The website is found at
http://www.sportsartamerica.com There you can find a dealer/service depot in your area.

hi
check inline fuse
if you start it and incline reads more than o when pressed it is fuse
it is lokacted on motor controll board
there is 2 one for drive motor one for elevation motor
cll if assistance needed 347 515 8670