Proform 530 Treadmill Walking Belt - Answered Questions & Fixed issues
Stop button, fan button, up incline button are not
If some buttons work, you more than likely have a key pad problem. Unfortunately Icon doesnt sell kep pad seperately. As a last effort, try heating up those buttons wit a blow dryer. This will work temp. sometimes.
1/26/2015 9:54:19 PM •
Proform 530...
•
Answered
on Jan 26, 2015
•
1,663 views
My treadmill starts up and
check tension on w/belt and motor belt signs of worn out belt. black dust cracking treads or flaking.
3/14/2011 2:25:28 AM •
Proform 530...
•
Answered
on Mar 14, 2011
•
442 views
Belt slips when walking on it.
there's a wrench that came with it, an allen wrench, turn on betl at medium slow speed, go to rear of treadmill and using the wrench give at each end caps(there is a hole to put the wrench) a half a turn on each side several time and walk in it until belt remains stable.
2/8/2011 11:09:49 PM •
Proform 530...
•
Answered
on Feb 08, 2011
•
218 views
I have a proform 350
The roller is not difficult to replace, it is also no really expensive.
Part number is #219035 it is around $80 from the manufacturer.
The phone number to order the part will be found on the model/serial number tag on your treadmill.
When folded, there is a tag on the frame of the treadmill with a correct model and serial number and the 1-800......
1/9/2011 4:53:39 AM •
Proform 530...
•
Answered
on Jan 09, 2011
•
319 views
I folded the machine for
Just adjust the rear roller bolts until the belt is centered and can be lifted in the middle 2"-3".
8/11/2010 2:21:04 AM •
Proform 530...
•
Answered
on Aug 11, 2010
•
348 views
Belt is slipping, how do
Hi,
This is dinesh from AADHI FITNESS SERVICE CENTRE...
Search for the details in justdial india...
Need some allignment and service for ue machine...
Contact no is 9986202487
7/29/2010 5:31:36 AM •
Proform 530...
•
Answered
on Jul 29, 2010
•
154 views
The belt on my treadmill keeps slipping/moving to
At the back of the treadmill, there are 2 adjustment screws, 1 on each side. They are used to move each end of the rear roller either forwards or backwards. I typically teach people to use the left hand adjustment screw because the direction you turn the screw is the direction the treadbelt will move. Turn the machine on and run it at the lowest speed, usually .5mph and while it's running, make an slight adjustment. If it's running while you do it, you will be able to watch the progress of the belt and it's easier to fine tune it this way. Using an allen key (you should have been supplied one with the machine) turn the adjustment bolt a 1/4 turn in the direction you want the belt to go (only from the left). Wait a few minutes and watch it carefully, you do not want it to run up against the side rails of the machine, this will shred the sides of the belt. You really shouldn't need to turn it more than a 1/4-1/2 turn to make an adjustment. Watch the belt migrate back towards the center and when it gets close, turn the screw slightly back a bit to stop the progress, or it will stop on it's own as it reaches the higher angle of the roller. Patience is key here, don't try to do it one morning on your way out to work. Give yourself 15-20min to focus on it and remember that as long as you don't use large adjustment increments and pay attention to where the belt is headed, you'll be fine.
6/2/2010 3:24:50 AM •
Proform 530...
•
Answered
on Jun 02, 2010
•
8,193 views
Have a PFTL5123 Proform 530 with console not worki...
Go to iconservice.com click on replacement parts, the console part # differs from yours the part # shown is 207885 out of stock . You may want to call them @ 1-800-999-3756 to confirm the correct part #.
If you getting ff or 2f then you have a Eprom problem unfortunately some components are proprietary and cannot be found. So replacement is your only option.
5/24/2010 6:54:25 AM •
Proform 530...
•
Answered
on May 24, 2010
•
360 views
My walking belt is off cener
Here are two solutions one is to get the belt centered on the treadmill
and the other is to tighten the belt.
There should be two bolts
in the rear of the treadmill, one on each
side. These bolts adjust the rear roller of the treadmill. The walking
belt will always go to the side that is looser. To get the belt back
on track, (if you can start the treadmill so the belt is running)
tighten the bolt on the side that the belt has slipped to. Tighten the
bolt a little bit at a time. If you tighten the bolt too much, then the
belt will go to the other side.
To tighten the belt, start by
locating the two bolts that adjust the
rear roller (one on each side of the unit in the back). Run the unit at
about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that
what you do to one side, you MUST do to the other side or the belt will
get off center. After you tighten it 1/4 turn, check the belt to see if
it is still slipping. If it is then tighten the belt 1/4 turn again.
Continue until the belt does not slip, but do not tighten the bolts more
than 2 full turns.
5/7/2010 9:41:51 PM •
Proform 530...
•
Answered
on May 07, 2010
•
633 views
How do you calibrate a ProForm 530x Treadmill?
To calibrate the speed and/or incline, please refer to the instructions that are under the motor hood cover or are mounted on the inside of the belly pan. Be sure to unplug your machine. If the instructions are not there, please contact our customer service department at {~1-888-533-1333} while you are near your machine.
4/11/2010 5:09:53 AM •
Proform 530...
•
Answered
on Apr 11, 2010
•
628 views
Proform 530 powers up but won't start
If it lights up, incline works and counts like it's going but no belt movement it's your motor controller. If it's not doing these things then I need to know what it's doing or not doing.
10/12/2013 12:29:02 PM •
Proform 530...
•
Answered
on Oct 12, 2013
•
922 views
Not finding what you are looking for?